7
. ATTACH THE COLUMN ASSEMBLIES
PAGE 1 OF 3
. DO NOT OVER-
STEP 4:
AT 4" FROM THE BOTTOM OF THE
CORDLESS DRILL WITH
DETAIL A
. INSERT THESE THROUGH THE HOLES ON EACH END OF THE
. USE THE HEX HEAD DRIVER BIT OR THE
FULLY TIGHTEN.
STEP 6:
TIGHTEN THE SOCKET SCREWS
* 17 ON 60" OR 72" WORKSTATION
.
INSERT (2) END CAPS
LEVEL
1
WORKSURFACE SUPPORT AS SHOWN IN THE DETAIL BELOW LEFT AND FULLY
WRENCH
SPECIAL EXCEPTION: ON WORKSTATIONS ON
AND THREAD THEM INTO THE HOLES IN THE T-SLOT PLATES
ALLEN WRENCH PROVIDED
ALLOW FOR CLEARANCE OF THE EQUIPMENT.
5
8
#2 PHILLIPS HEAD DRIVER BIT OR
CROSS SUPPORT
AND
7/32" HEX HEAD BIT OR ALLEN
STEP 5:
TO THE WORKSURFACE USING (16) WOOD SCREWS
*** ONLY ON 60" OR 72" WORKSTATIONS
5
** 1 ON 60" OR 72" WORKSTATION
2
3
2
3
PRE-INSTALLED IN THE COLUMN ASSEMBLIES
.
INTO THE ENDS OF THE CROSS SUPPORT
TAPE MEASURE
VERSION DATED: 9/8/11
. SEE DETAIL A. DO NOT
WHICH THE LifeBalance STATION IS BEING INSTALLED, THE CROSS SUPPORT
DO NOT OPERATE THE UNIT UNTIL IT IS FULLY ASSEMBLED.
TIGHTEN THE SCREWS. USE A LOW TORQUE SETTING ON THE DRILL.
14
LEVEL THE CROSS SUPPORT
TOOLS REQUIRED FOR ASSEMBLY:
4
4
ALIGN THE HOLES IN THE WORKSURFACE SUPPORTS WITH THE PILOT
AND
4
INSTRUCTION # 50591
READ ALL OF THE INSTRUCTIONS BEFORE BEGINNING
#2 SQUARE HEAD DRIVER BIT
HOLES IN THE WORKSURFACE
SHOULD BE ATTACHED RESTING ON THE FEET OF THE COLUMN ASSEMBLIES TO
NewHeights ELECTRIC HEIGHT ADJUSTABLE WORKSTATION ASSEMBLY INSTRUCTIONS:
STEP 1:
LAY THE WORKSURFACE
1
ON A PROTECTED SURFACE WITH THE PILOT
HOLES FACING UP.
STEP 2:
PLACE THE COLUMN ASSEMBLIES
2
AND
3
ON THE WORKSURFACE
WITH THE FEET FACING UP. THE MOTOR WIRES MUST FACE THE INSIDE OF THE
WORKSTATION.
STEP 3:
WITH THE HELP OF AN ASSISTANT, PLACE (4) STAR WASHERS
6
ON (4)
SOCKET SCREWS
ITEM # PART #
DESCRIPTION
QTY.
1
VARIES WORKSURFACE
1
2
VARIES NewHeights COLUMN ASSY LEFT HAND
1
3
VARIES NewHeights COLUMN ASSY RIGHT HAND
1
4
VARIES NewHeights CROSS SUPPORT
1
5
52470 3/8-16 x 3/8 BUTTON HEAD SOCKET SCREW
4
6
52477 3/8 INTERIOR TOOTH STAR WASHER
4
7
800411 NewHeights/HOVER END CAP
2
8
51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW 19 OR 17*
9
50285 NewHeights HAND SWITCH
1
10
50072 8 x 3/4 PHILLIPS PAN HEAD RECEX DRIVE SCREW
4
11
51951 WIRE MANAGEMENT J
3 OR 1 **
12
VARIES 42" OR 54" U-CHANNEL
1 ***
13
52498 7/32" ALLEN WRENCH
1
14
50298 NewHeights 2-LEGGED CONTROL BOX
1
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: 800.298.4351 FAX: 866.882.9475
www.raproducts.com
K&A MANUFACTURING
FOOT
5
7
STEPS 1-6
1
MOTOR WIRES
SUPPORT
WORKSURFACE
8
BACK
3
4
6
2
A
LOCATING THE CROSS SUPPORT
4
(SEE EXCEPTION IN STEP 4)
BOTTOM OF
WORKSURFACE
SUPPORT
HARDWARE PACK # 52226
4.00
PRE-INSTALLED
T-SLOT PLATE
