R.V.R. Elettronica HC04CH-FM Скачать руководство пользователя страница 6

2

 

/ 24

User Manual

Rev. 1.0 - 29/01/21

HC04CH-FM

ELETTRONICA

The customer always assumes the risks of loss 

(i.e., R.V.R. is never liable for damage or loss), until the 

package reaches the R.V.R. facility. For this reason, we 

suggest that you insure the goods for their full value. 

The goods must be shipped, using C.I.F. values (PAID IN 

ADVANCE),  to  the  address  specified  by  the  R.V.R. 

service manager on the authorization.

 

The equipment must not be returned without the 

authorization for sending as it may be returned to 

the sender.

4  Make sure to include a descriptive technical report 

mentioning any issues encountered and a copy of 

your original invoice indicating the date from which the 

warranty is valid.

Spare parts and parts under warranty can be ordered at 

the following address. Make sure to include the model and 

serial number of the equipment, as well as the description 

and number of spare parts.

 

R.V.R. Elettronica 

Via del Fonditore, 2/2c 

40138 BOLOGNA ITALY 

Tel. +39 051 6010506

 

3.  First aid

Personnel entrusted with installation, use, and maintenance 

of the equipment must be familiar with first aid theory and 

practices.

 

3.1  Treatment of electric shocks

 

3.1.1  If the victim has lost consciousness

Follow the first aid principles below.

• 

Place the victim lying on their back on a hard 

surface.

• 

Open the airway by lifting the neck and pushing 
the forehead back (

Figure 1

). 

Figure 1

• 

If necessary, open their mouth and check their 

breathing.

• 

If  the  victim  is  not  breathing,  start  artificial 

respiration immediately (

Figure  2

): tilt the 

head, close the nostrils, make your mouth 

adhere to that of the victim and perform 4 quick 

breaths.

Figure 2

•  Check the heart rate (

Figure  3

); in the 

absence of a heartbeat, immediately begin 

heart massage (

Figure  4

) by compressing 

the sternum approximately in the centre of the 

chest (

Figure 5

).

 

 

Figure 3

 

Figure 4 

Figure 5

• 

In the case of only one rescuer, this person 

must maintain a rhythm of 15 compressions 

alternating with 2 quick breaths.

• 

In the case of two rescuers, the rhythm must 

be one breath every 5 compressions. 

• 

Do not interrupt heart massage during artificial 

respiration.

• 

Call a doctor as soon as possible.

 

3.1.2  If the victim is conscious

• 

Cover the victim with a blanket.

• 

Try to keep the victim calm.

• 

Loosen the clothes and place the victim in a 

lying position.

• 

Call a doctor as soon as possible.

 

3.2  Treatment of electrical burns

 

3.2.1  Extensive burns and cuts to the skin

• 

Cover the affected area with a clean sheet or 

cloth.

• 

Don’t break blisters; remove fabric and items of 

clothing adhering to the skin; apply a suitable 

ointment.

•  Treat the victim as required for the type of 

injury.

• 

Transport the victim to the hospital as quickly 

as possible.

• 

If the arms and legs have been affected, keep 

them elevated.

If medical help is unavailable for an hour and the victim is 

conscious and not retching, administer a liquid solution of 

salt and baking soda: 1 teaspoon of salt and half a teaspoon 

of baking soda for every 250ml of water.

Slowly drink about half a glass of solution four 

times over a period of 15 minutes. 

 

Discontinue if retching occurs.

Do not give alcohol.

 

3.2.2  Less serious burns

• 

Apply cold (not icy) gauze compresses using 

as clean a cloth as possible.

• 

Don’t break blisters; remove fabric and items of 

clothing adhering to the skin; apply a suitable 

ointment.

• 

If necessary, put on clean and dry clothes.

•  Treat the victim as required for the type of 

injury.

• 

Transport the victim to the hospital as quickly 

as possible.

• 

If the arms and legs have been affected, keep 

them elevated.

Содержание HC04CH-FM

































Отзывы: