manualshive.com logo in svg

R/Evolution 2000 Series, Руководство по началу работы

Поделиться
Скачать
R/Evolution 2000 Series Скачать руководство пользователя страница 51

Appendix A

Hardware Components and LEDs

51

Drive Enclosure Components and LEDs

A drive enclosure can be connected to a controller enclosure or to another drive 
enclosure to provide additional disk storage capacity. Table A-5 describes the drive 
enclosure components.

The components and LEDs on the front of a drive enclosure are the same as on a 
controller enclosure; see Figure A-1 and Table A-2.

Table A-5 

Drive Enclosure Components

Description

Quantity

Expansion (I/O) module

1 or 2

1

1 Air-management system drive blanks or I/O blanks must fill empty slots to maintain optimum airflow through the chassis.

SAS or SATA drive module

2–12 per enclosure

AC power and cooling module

2 per enclosure

3-Gbps, 4-lane SAS In port

1 per expansion module

3-Gbps, 4-lane SAS Out port

1 per expansion module

Service port (RS-232 micro-DB9)

1 per expansion module

Содержание 2000 Series



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды