Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-WKF8407EK
For Style WKF8407EK
2017 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Crossbar Assembly
x 1
Please go to
for product cleaning tips. Go to the
selection.
(1) A19 Medium Base bulb 100W Maximum or
(1) Medium Base Vintage bulb is recommended but not supplied.
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
www.quoizel.com
Care + Maintenance
Light Source:
Estimated Assembly Time:
Preparation:
Fixture can only be mounted in the direction indicated on page 2.
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
C
Fixture Body
x 1
Figure 3
B
Alternate
Mounting screw
x 2
ReleasedDate:2017-09-29
D
Cage with
Glass Panels
x 1
STEP 1
Install Bulb and Cage
-
A. Remove lock screws from the Fixture Body (C).
B. Insert the bulb onto the socket and screw snugly into place.
C. Align the label “A” on the top edge of the Cage (D) to the label “A” in
the bottom edge of the fixture hood. Attach the Cage (D) to the fixture
hood and secure with previously removed lock screws. Hand tighten
until snug with screwdrivers.
C
D
Lock Screw
Vintage Bulb
(recommended
but not supplied)
Socket
Figure 1
Label “A”
Label “A”
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
A
Mounting Screw
or Alternate Short
Mounting Screw
STEP 2
Installing the Crossbar Assembly
-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Figure 2
STEP 3
Test Fit the Backplate to the Crossbar Assembly
-
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (C) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (C) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screw or
alternate short mounting screw on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws in
or out of the crossbar until the correct length is achieved. Once the
backplate and Fixture Body (C) is secure, remove the mounting ball
and Fixture Body (C) and proceed to Step 4.
C
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Mounting Screw
or Alternate Short
Mounting Screw
