Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-SNN8406
For Styles SNN8406K, SNN8406PN and SNN8406W
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Please go to
for product cleaning tips. Go to the
selection.
(1) A19 Medium Base bulb 100W Maximum.
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
www.quoizel.com
Care + Maintenance
Light Source:
Estimated Assembly Time:
Preparation:
Fixture can only be mounted in the direction indicated.
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
STEP 2
Fit Backplate to
Crossbar Assembly
-
A.
on Fixture Body (B) to
the
Remove mounting balls from the
Crossbar Assembly (A). Fit the
backplate
Crossbar Assembly (A) and
secure with mounting balls.
Note: The backplate
should be snug against
the wall and the mounting balls.
If
on Fixture
Body (B)
not, adjust the length of the
mounting screw on the Crossbar
Assembly (A) by unscrewing the
preassembled hex nut and lock
washer and then screwing the
Figure 2
mounting screws in or out of the crossbar until the correct length is
achieved. Once the backplate on Fixture Body (B) is secure, remove
the mounting ball and Fixture Body (B) and proceed to Step 3.
Mounting
Screw
B
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 4
STEP 4
Install Fixture Body
-
A. Carefully tuck all wires into the outlet box and position the
backplate of Fixture Body (B) over the outlet box. Align the holes in
the backplate with the mounting screws. Place caulk (not supplied)
into the previously removed mounting balls and then attach Fixture
Body (B) using the mounting balls. Hand tighten until snug.
Mounting Screw
B
Mounting Ball
A
Backplate
2018 QuoizelInc.
ReleasedDate:2018-11-12
visit us on-line at www.quoizel.com
Package Contents
B
Fixture Body
x 1
STEP 1
Install Crossbar Assembly
-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(C). Tighten until snug
.
Supply Wires
with Ground Wire
Outlet
Box
Figure 1
A
C
Crossbar
Assembly
x 1
A
Alternate
Mounting
Screw
x 2
E
Outlet Box Screw
x 2
C
Wire Connector
x 3
D
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (D) to make all wire connections.
Twist connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
