1of2
Assembly Instruction Sheet #IS-LTE8407PN
For Style LTE8407PN
2016 QuoizelInc.
Please go to
for product cleaning tips. Go to the
selection.
(1) Medium Base 100W bulb Maximum.
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
www.quoizel.com
Care + Maintenance
Light Source:
Estimated Assembly Time:
Preparation:
Fixture can only be mounted in the direction indicated on page 2.
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Package Contents
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Crossbar Assembly
x 1
B
Fixture
Body
x 1
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
Figure 5
C
Shade
x 1
STEP 2
-
Remove Styrofoam
inside of the Fixture
Body
A. Remove the Shade (C) and
Styrofoam inside the Fixture
Body (B).
Styrofoam
C
B
Figure 2
B
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 3
B
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
ReleasedDate:2016-11-03
STEP 1
Install Crossbar Assembly
-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 1
A
STEP 3
Fit Backplate to Crossbar Assembly
-
A. Remove mounting balls from the Crossbar Assembly (A). Fit the
backplate on Fixture Body (B) to the Crossbar Assembly (A) and
secure with mounting balls. Note: The backplate on Fixture Body (B)
should be snug against the wall and the mounting balls. If not,
adjust the length of the mounting screw on the Crossbar Assembly
(A) by unscrewing the
preassembled hex nut and
lock washer and then
screwing the mounting
screws in or out of the
crossbar until the correct
length is achieved. Once
the backplate on Fixture
Body (B) is secure, remove
the mounting ball and
Fixture Body (B) and
proceed to Step 4.
Mounting
Screw
STEP 5
Install Fixture Body
-
A. Carefully tuck all wires into the
outlet box and position the
backplate of Fixture Body (B)
over the outlet box. Align the
holes in the backplate with the
mounting screws. Place caulk
(not supplied) into the
previously removed mounting
balls and then attach Fixture
Body (B) using the mounting
balls. Hand tighten until snug.
Mounting
Screw
