QuickLabel Systems QLS-4100 Скачать руководство пользователя страница 50

Страница: 50 / 215

4-6

Keypad controls and menus

Operation Menu

Options are available in a Pause state only.

Pull Back

Requires special hardware. Contact QuickLabel for
more information on this function.

Label Reprint

Reprints up to 999 copies of the last label printed, if
using the Windows print driver.

Synchronize Labels

Synchronizes labels when using printer/applicator
or Print & Peel.

Ribbon Menu

Options are available in a Pause state only.

Ribbon Type

Selects printhead intensity tailored to a specific
media type. Possible values are Standard and
Resin/Synthetic.

Drop/Lift Adjust

Adjust the drop and lift point for printheads 1 – 4.
Possible values are 0 to +40 mm.

Ribbon Sensor

Used by QuickLabel technicians when performing
factory diagnostics. Possible values are Enabled
and Disabled, but in general use, the sensor should
always be enabled.

Communications
Menu

Options are available in a Pause state only.

Data Port

Selects the data input interface used by the printer.
Possible values are Parallel, Serial, or Ethernet.

Parallel Mode

Specifies the mode of connection for the parallel
port. Possible values are Auto or Standard.

RS232 Baud Rate

Specifies a baud rate for the RS232 serial port.
Possible values are 4800, 9600, 19200, or 38400.

RS232 Handshaking

Specifies a handshaking method for the RS 232
serial port. Possible values are Hardware or
XON/XOFF.

TCP/IP Address

Specifies the IP address of the printer for ethernet
purposes.

Содержание QLS-4100
























































































































































































































Результаты поиска

Содержание QLS-4100

Отзывы:

QuickLabel Systems QLS-4100, Инструкция по эксплуатации и установке, Страница: 50 / 215

Результаты поиска

Содержание QLS-4100

Отзывы: