QuickJack BL-3500SLX Скачать руководство пользователя страница 19

Страница: 19 / 72

QuickJack™ Portable Car Jack

P/N 5900959 — Rev. L1 — December 2020

QuickJack Box 3 (and Parts Bag)

Many of the items you will be using during initial setup come in Box 3; the Parts Bag is included

in Box 3.
The

QuickJack Box 3

includes:

•

A Power Unit (Voltage of your choice, decided at time of purchase)

•

Four Medium Rubber Lift Blocks and Four Tall Rubber Lift Blocks

•

Two Short Hydraulic Hoses and Two Long Hydraulic Hoses

The

QuickJack Parts Bag

includes:

•

Four Female Quick-Connect Fittings

•

Two Male Quick-Connect Fittings

•

Two Power Unit Quick-Connect Fittings

•

Two Hydraulic Elbow Fittings

•

Bottle of Liquid Thread Sealant

Air and Hydraulic Cylinders

Each QuickJack Frame has one Air Cylinder and one Hydraulic Cylinder.

The components of the Air and Hydraulic Cylinders are:
•

Air Inflation Valve

. Used to add air pressure to the Air Cylinder. Comes with the appropriate

valve (also called a Schrader® valve) installed.

•

Hydraulic Cylinder Connector

. Hydraulic Elbow Fitting attaches here. Use a 6 mm hex key to

remove the shipping plug before installing the Hydraulic Elbow Fitting.

•

Bleeder Screw

. Used to “bleed” the air from the Hydraulic System, if necessary. Refer to

Troubleshooting

for more information.

Содержание BL-3500SLX








































































Результаты поиска

Содержание BL-3500SLX

Отзывы:

Похожие инструкции для BL-3500SLX

Бренды по названию

Популярные бренды

QuickJack BL-3500SLX, Руководство по установке и эксплуатации

Результаты поиска

Содержание BL-3500SLX

Отзывы:

Похожие инструкции для BL-3500SLX

Бренды по названию

Популярные бренды