Quickie QM-7 Series Скачать руководство пользователя | Manualshive

Страница: 39 / 83

background image

QM-7 SERIES SERVICE MANUAL

PAGE 4.5

JANUARY 2012

SUNRISE MEDICAL

Section 4

Trip Text

Corrective Action

Over-current

This fault occurs when the limits of an actuator circuit is exceeded.

Perform

Tilt Will Not Operate

troubleshooting section of this manual to

test the end of travel limit switches.

Overtemp. (Acts)

This error indicates that the Intelligent Seating Module (ISM) has become
excessively warm. Note: An ISM is only required when there are more
than 2 actuators and may not be mounted on this power chair. Allow the
unit to cool. If the error repeats, the actuator may be defective or over
loaded.

Overtemp. (Lamps)

Note: This fault can only occur if an Intelligent Seating Module is used on
this power chair and connected to external lights.

DIME Error

This error indicates that one or more of the modules are not compatible.
Remove the last module installed and retest. Recycle the power. If this
error persists, Contact Sunrise Technical Service for assistance.

Memory Error

Recycle the power. Verify that cables are correctly mated. If a module
has been replaced recently, it may be defective. If error persists, contact
Sunrise Technical Service for assistance.

PM Memory Error

Recycle power. Verify cables are correctly mated. If a module has been
replaced recently, that module may be defective. If error persists, contact
Sunrise Technical Service for assistance.

Bad Cable

Inspect and replace the defective cable(s).

Bad Settings

Verify that programming agrees with installed equipment. If all settings
are correct, the control module may be defective. If error persists, contact
Sunrise Technical Service for assistance.

Module Error

Recycle power. Verify that cables are correctly mated. If a module has
been replaced recently, it may be defective. If error persists, contact
Sunrise Technical Service for assistance.

System Error

Recycle power. Verify that cables are correctly mated. If a module has
been replaced recently, it may be defective. If error persists, contact
Sunrise Technical Service for assistance.

SID Detached

The Omni has detected that a specialty control has become disconnected.
Recheck all cables. If the error is still present, replace the specialty
control.

User Switch Detached

Indicates that a user switch has become disconnected. Find the
disconnected switch and reconnect.

Gone to Sleep

The predetermined sleep time has been exceeded due to inactivity by the
user.

Charging

This indication is present when the battery charger is connected. There
may also be an error in the control module. If error persists, contact
Sunrise Technical Service for assistance.

Table 1- R-NET Error Codes (Cont.)

«
...
37
38
39
40
41
...
»

Содержание QM-7 Series




















































































Отзывы:

Нет отзывов

Похожие инструкции для QM-7 Series

Бренд: Decon wheel Страницы: 5

Бренд: Pride Страницы: 43

Бренд: Pride Страницы: 43

Integrated C.G. Tilt P-222SE

Бренд: Quickie Страницы: 36

Бренд: Quickie Страницы: 60

Бренд: Quickie Страницы: 64

Бренд: Küschall Страницы: 44

Бренд: Küschall Страницы: 116

Бренд: Quantum Страницы: 24

Бренд: Pride Страницы: 43

Бренд: EZee Life Страницы: 5

Бренд: EZee Life Страницы: 8

Бренд: EZee Life Страницы: 6

Бренд: Rehab Страницы: 2

Бренд: Rehab Minimaxx Страницы: 16

Бренд: Quickie Страницы: 29

Бренд: Drive DeVilbiss Healthcare Страницы: 12

Бренд: C.T.M. Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды