Quickie QM-7 Series Скачать руководство пользователя

Страница: 12 / 83

QM-7 SERIES SERVICE MANUAL

PAGE 1.8

JANUARY 2012

SUNRISE MEDICAL

•

Batteries function as a power wheelchair’s
fuel tank. The larger the group size, the
farther the wheelchair will go.

•

Use the size speci

ed by the wheelchair

manufacturer. Never use undersized
batteries

•

This chair uses either 22NF, or GRP 24
Batteries. Flat-top batteries help lower the
seat to

oor height.

•

Deep-cycle batteries used in wheelchairs
are designed to be discharged and
recharged on a regular basis.

•

Starting or automotive type batteries use a
rapid burst of power to start an engine and
are quickly recharged by an alternator or
generator. They are rated by cold cranking
amps, a measure that has no relevance to
wheelchair application.

•

Marine and RV batteries frequently are
not deep-cycle as they are often used for
starting engines.

•

Only use Deep-Cycle sealed type
batteries in a wheelchair.

Battery Types

IT IS THE RESPONSIBILITY OF THE INSTALLER TO KNOW WHAT KIND OF BATTERIES TO
INSTALL IN A CUSTOMER’S WHEELCHAIR!

• •

Batteries installed incorrectly can blow the

Batteries installed incorrectly can blow the
fuse for this system. Pay careful attention

fuse for this system. Pay careful attention
to install the battery harness across both

to install the battery harness across both
batteries instead of to each of the batteries

batteries instead of to each of the batteries
individually. See Section 7 for correct

individually. See Section 7 for correct
Battery Removal and/or Installation

Battery Removal and/or Installation

Section 1

Battery Size

Battery Installation

Содержание QM-7 Series




















































































Результаты поиска

Содержание QM-7 Series

Отзывы:

Похожие инструкции для QM-7 Series

Бренды по названию

Популярные бренды

Quickie QM-7 Series, Руководство по обслуживанию

Результаты поиска

Содержание QM-7 Series

Отзывы:

Похожие инструкции для QM-7 Series

Бренды по названию

Популярные бренды