Quickie Integrated C.G. Tilt P-222SE Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 36

background image

F

D

E

K

L

H

I

J

930476 Rev. E

14

P-222

IX. SET-UP, ADJUSTMENT & USE

A. POWER DRIVE UNIT

Wheelchair and Power Drive Attachment

a. Position seat and main frame over power drive unit.
b. Align quick-connect blocks (A) with binding socket (B) located on power drive unit.
c. Ensure frame is properly located on power drive unit and the controller cable is clear.
d. Press levers (C) down until locked.
e. Lever force required can be adjusted by adjusting screw.
f.

Connect harnesses between seat and base.

WARNING

Always secure levers before operating chair. If the chair fails to operate and the
battery charge indicator flashes 9 bars, check both quick-connect levers for
securement. Then cycle the on/off switch.

B. BATTERY REMOVAL

To remove the batteries for transporting or servicing:

Remove Batteries

a. Remove seat and main frame from power drive unit using quick-release levers (D).
b. Lift battery compartment lid (E) off of power drive unit.
c. Prevent the power drive unit from tipping forward by placing a solid object underneath

the front of the power drive unit.

d. Disconnect battery leads from power harness.
e. Lift rear most battery out using the battery straps (F).
f.

Pull the front battery rearward, disconnect it, and remove it using the battery straps.

WARNING

Batteries may weigh up to 55 lbs. (25 kg). Care must be taken to avoid injury
when lifting.

C. FOLDING BACKREST

Quickie P-222 SE wheelchairs are shipped with backrest in folded position.

1. Upright Positioning

a. Lift backrest to upright position so that latch handles (G) lock into place.
b. Backrest is ready for use.

2. Folding Backrest

a. Lift and turn backrest latch handles (G) inward or outward.
b. Fold backrest forward.

WARNING

CAUTION: Backrest latches must be locked into place before operating wheel-
chair.

D.SWING-AWAY FOOTRESTS

1. Installation

a. Place swing-away pivot pin (H) into the locating hole (I) on top of the hanger mount

with the footrest facing outward from frame.

b. Rotate the footrest inward until latch plate locks (J) into place on locking bolt.

2. Removal

a. To remove footrest, press quick-release lever (K).
b. Rotate footrest outward and lift.

3. Height Adjustment

a. Remove both bolts (L) in the hanger frame tube.
b. Reposition footrest height.
c. Re-tighten all bolts (L).

1

2

3

4

5

6

A

C

B

G

1

2

3

4

5

6

«
...
12
13
14
15
16
...
»

Содержание Integrated C.G. Tilt P-222SE





































Отзывы:

Нет отзывов

Похожие инструкции для Integrated C.G. Tilt P-222SE

ATLANTIS PR46070

Бренд: Able 2 Страницы: 2

Бренд: Stylus Страницы: 24

Бренд: Safer Locks Страницы: 2

Бренд: R Healthcare Страницы: 41

Бренд: dynarex Страницы: 2

Linido 200550313

Бренд: Direct Healthcare Group Страницы: 12

Varilite Icon Mid Back

Бренд: ALLIED MEDICAL Страницы: 5

Lumex TENDERFLO WATER CUSHION

Бренд: Graham Field Страницы: 2

Mini Tilt Wheelchair

Бренд: Tendercare Страницы: 28

Triride 1560507

Бренд: Gianni Страницы: 56

Бренд: Travel Buggy Страницы: 13

Бренд: Revab Страницы: 38

Бренд: Revab Страницы: 132

Бренд: Moretti Страницы: 4

Бренд: Deming Designs Страницы: 11

Бренд: Observer Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды