Quectel M50 Скачать руководство пользователя

Страница: 9 / 89

M50 Hardware Design

M50_HD_V2.0

- 9 -

1. Introduction

This document defines the M50 module and describes the hardware interface of M50 which are

connected with the customer application and the air interface.

This document can help customers quickly understand module interface specifications, electrical

and mechanical details. Associated with application notes and user guide, customers can use

M50module to design and set up mobile applications easily.

1.1. Related documents

Table 1: Related documents

Document name

Remark

[1]

M50_ATC

AT commands set

[2]

ITU-T

Draft new

recommendation V.25ter

Serial asynchronous automatic dialing and control

[3]

GSM 07.07

Digital cellular telecommunications (Phase 2+); AT

command set for GSM Mobile Equipment (ME)

[4]

GSM 07.10

Support GSM 07.10 multiplexing protocol

[5]

GSM 07.05

Digital cellular telecommunications (Phase 2+); Use

of Data Terminal Equipment – Data Circuit

terminating Equipment (DTE – DCE) interface for

Short Message Service (SMS) and Cell Broadcast

Service (CBS)

[6]

GSM 11.14

Digital cellular telecommunications (Phase 2+);

Specification of the SIM Application Toolkit for the

Subscriber Identity module – Mobile Equipment (SIM

– ME) interface

[7]

GSM 11.11

Digital cellular telecommunications (Phase 2+);

Specification of the Subscriber Identity module –

Mobile Equipment (SIM – ME) interface

[8]

GSM 03.38

Digital cellular telecommunications (Phase 2+);

Alphabets and language-specific information

[9]

GSM 11.10

Digital cellular telecommunications (Phase 2); Mobile

Station (MS) conformance specification; Part 1:

Conformance specification

[10]

GSM_UART_AN

UART port application note

[11]

GSM_FW_Upgrade_AN01

GSM Firmware upgrade application note

[12]

M10_EVB_UGD

M10 EVB user guid

Quecctel

Confidential

Содержание M50


























































































Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды

Quectel M50, Проектирование аппаратного обеспечения

Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды