Quectel EM05 Скачать руководство пользователя страница 53

Страница: 53 / 60

LTE Module Series

EM05 Hardware Design

EM05_Hardware_Design Confidential / Released 52 / 59

6.8. ESD Characteristics

The following table shows the ESD characteristics of EM05.

Table 32: ESD Characteristics of EM05

For a good ESD performance, the module mounting holes must be used to attach the device to the main

PCB ground closely.

6.9. Thermal Consideration

EM05 is designed to work over an extended temperature range. In order to achieve a maximum

performance while working under extended temperatures or extreme conditions (such as with maximum

power or data rate, etc.) for a long time, it is strongly recommended to add a heat sink (a thermal

compound or pad must be used between the module and the metal heat sink) between the module and

the main PCB for thermal dissipation.

Please add ground vias as many as possible on PCB for better heat dissipation. It is NOT recommended

to apply solder mask on the main PCB below the thermal dissipation area of EM05, and the module

should be kept away from heating sources.

Part

Contact Discharge

Air Discharge

Unit

Power Supply and GND

+/-4

+/-10

Antenna Interface

+/-4

+/-8

Others

+/-0.5

+/-1

NOTE

Quectel

Confidential

Содержание EM05





























































Результаты поиска

Содержание EM05

Отзывы:

Бренды по названию

Популярные бренды

Quectel EM05, Проектирование аппаратного обеспечения

Результаты поиска

Содержание EM05

Отзывы:

Бренды по названию

Популярные бренды