QUATRO
Air Technologies Inc.
----------------------------------------------------------------
Engineers Of Clean Air
----------------------------------------------------------------
30 Hymus Boulevard, Montreal, Quebec, H9R 1C9 Tel.: (514) 630-4444 Fax: (514) 630-4454 website:
www.quatroair.com
RESETTING MICROPROCESSOR CONTROLLER AFTER REPLACING MOTORS
Resetting Microprocessor After Motor Replacement WHILE “Service Motor(s)” Led is SOLID
1- Ensure motor access door is closed
2- Plug power back to the unit
3- When you Press “POWER”, MOTOR WILL START, “Service Motor(s)” Led stays SOLID
4- While motor is operating, press & hold SPEED UP & DN simultaneously until unit BEEPS
(hold for 10+ seconds, when beeping continuously, release)
5- In this condition, “System ON” Led is FLASHING, “Service Motor(s)” led is SOLID
6- Press SPEED DN (once) until “Service Motor(s)” Led is FLASHING and system is BEEPING continuously
7- Press & HOLD POWER button while “Service Motor(s)” is FLASHING & BEEPING continuously
Release, when it stops BEEPING, and motor operates in LOW speed
8- Operate unit at LOW SPEED for 10-15 minutes to break-in new brushes (to prolong brush life)
Resetting Microprocessor After Motor Replacement,
WHILE “Service Motor(s) Led is OFF
1- Ensure motor access door is closed
2- Plug power back to the unit
3- When you Press “POWER”, MOTOR WILL START
4- While motor is operating, press & hold SPEED UP & DN simultaneously until unit BEEPS
(hold for 10+ seconds, when beeping continuously, release)
5- In this condition, “System ON” Led is FLASHING
6- Press SPEED DN (once) until “Service Motor(s)” Led is FLASHING
7- Press & HOLD POWER button while “Service Motor(s)” is FLASHING
Release, when it stops BEEPING, and motor operates in LOW speed
8- Operate unit at LOW SPEED for 10-15 minutes to break-in new brushes (to prolong brush life)
Unplug POWER cord from unit, Replace motor(s) as per instructions above, close motor access door.
MOTOR WILL DEFAULT TO LOWEST SPEED AFTER A RESET. YOU WILL PROLONG MOTOR BRUSH LIFE IF YOU BREAK THEM IN, SO IT IS ADVISED TO LET MOTOR
OPERATE AT LOWEST SPEED FOR 15 MINUTES
TROUBLESHOOTING, MECHANICAL GUIDE
Symptoms
Possible Cause
Suggested Solution
Unit will not start
Faulty power supply
Circuit breaker popped
Motor burnt
Brushes worn
Check breaker box
RESET circuit breaker on unit panel
Replace motor (PN: AB001)
Replace Brushes (PN: AB112)
Excessive noise
Turbine impeller contacting housing
Replace motor (PN: AB001)
Insufficient airflow
Obstruction in system
Clogged filter
Remove obstruction
Replace filter
Motor shuts off
Input amperage too high
Graphite crystal rods are consumed
Motor is burnt
Ensure filter is in place, reset circuit breaker
Replace rods (PN: AG112, 2/pkg)
Replace motor (PN: AB001)
Excessive airflow
Filter not in place
Install filter
Suction varies from workstation to workstation
Hose lengths between stations vary
Adjust damper or blast gate at each station equalizing suction
WARRANTY
QUATRO Air Technologies (QUATRO) warrants its equipment to be free from defect in material and workmanship under
normal use and service for a period of one year from date of shipment. QUATRO's obligation under this warranty shall be
limited to replacing any parts, thereof, which shall be demonstrated to have been defective. This is expressly in lieu of all
other warranties, express or implied, including the warranties of merchantability and fitness.
QUATRO claims no warranty as to merchantability or as to the fitness of the merchandise for any particular use and shall not
be liable for any loss or damage. No person, firm or corporation is authorised to assume for QUATRO any other liability in
connection with the sale of these goods. Equipment, parts and material manufactured by others and incorporated in
QUATRO's equipment are warranted by QUATRO only to the extent of the original manufacturer's liability to QUATRO.
Conditions and Limitations:
This warranty does not cover
abuse, misuse, maintenance negligence, improper assembly,
acts of vandalism, acts of God, fear wear, modifications of the equipment or installation of a part not recommended by
QUATRO, as well as operation of the equipment at voltages other than those specified by QUATRO
.
REPLACEMENT PARTS LIST
PowerStation 6
Description
PS625-23A6GH
HEPA Filters (2 required)
F022
WHITE Filter Bags (6 required)
AG149 (pak of 6)
YELLOW Filter Bags (6 required)
AG259-06 (pak of 6) or AG259-12 (pak of 12)
Blower Turbine Assy 230V (2 required)
(2) AB045-25
