Quatro 425L, Инструкция по эксплуатации и техническому обслуживанию

Страница: 2 / 14

QUATRO
Air Technologies Inc.
2
1- INTRODUCTION
You are now the owner of a QUATRO SPH Or AF System , an advanced effective indoor dust and fume collection system
designed specifically to remove particulate matter and odour causing gas phase contaminants at the source. You can expect
a noticeable improvement in air quality as the
SPH Or AF System begins the process of reducing microscopic airborne
particulate.
The
SPH or AF System normally features 3 Or 4 stages of filtration:
1) An OPTIONAL Pre Filter Pad OR Knock Out Pad. This captures large debris.
2) A Pre Filter for larger particles.
3) A HEPA filter captures & holds fine particles protecting the motor and ensuring a clean output.
4) A Chemical Filter to absorb & contain odour causing gas phase contaminants.
The filter sequence can be customized to your application. Contact Quatro Air for more info.
WARNING
–
To reduce the risk of damage to your system read and follow all instructions. Failure to follow these
guidelines may result in undesired operation or damage that will not be covered under warranty.
2-
WHAT’S IN THE BOX
The SPH model comes
with the “Laser Blue” Gel filter seal. The AF model comes with a gasket seal.
Both models are available with either 6” or 12” filter sections depending on the filter sequence for the application.
Models Name Accessories
426L
425L
4B6
4B5 SPH Or AF400
120V c/w “Long Life” Motors
SPH Or AF400
230V c/w “Long Life” Motors
SPH Or AF400
120V c/w “Brushless” Motor
SPH Or AF400
230V c/w “Brushless” Motor
(1) O&M Manual
(1) Power Cord
(2) Clamps Per Inlet
(No Clamps For 1.5”)
(1) Piece Of The Appropriate Size Hose (Per Inlet)
3- IMPORTANT SAFETY & INSTALLATION PRECAUTIONS
- Ensure to use proper voltage as indicated on the system.
- To reduce the risk of electric shock, do not expose to excessive moisture, water or rain.
- Use only on a grounded electrical circuit.
- Do not install or operate the system in an enclosed space or against a wall. Unit may overheat & shut down.
- Keep all objects a
t least 6” away from the casing, especially the discharge grill.
- All filters must be in place whenever this machine is in operation.
- ALWAYS turn system on/off switch to off and disconnect power prior to accessing unit, replacing filters, or servicing motor(s).
- Allow the unit to cool for 45 minutes before performing any service to the motor(s).
- Do not kink hose or restrict airflow in any way.
SAVE THESE INSTRUCTION FOR FUTURE REFERENCE
Failure to follow these guidelines may result in undesired operation or damage, not covered under this warranty.
4- INSTALLATION
1) Install the unit in the chosen location.
2) Open the filter access door & lid
and install the filters in the correct order. See the “Filter Service & Replacement”
section for more info.
3) Connect the supplied hose from the Quatro System to the Laser/Printer.
4) Connect the power cord to the unit and then to the power source.
VERIFY VOLTAGE BEFORE CONNECTING.
- ONLY USE THE POWER CORD SUPPLIED WITH THE EQUIPMENT.
- Always plug the unit directly into the wall outlet. Do not use extension cords or power bars.
- Ide
ally the unit should be plugged into it’s own dedicated circuit.
- The system is designed to be constantly powered (plugged in). The system will not function correctly and may get
damaged if power source is used to control the operation. See “Controls” for more info.
5) Turn unit on & adjust the desired airflow using the arrow up and down keys. Set airflow to lowest acceptable level to
properly evacuate your equipment.
For information abou
t remote operation see the “Controls” section.
WARNING: DO NOT OPERATE UNIT UNLESS ALL FILTERS ARE IN PLACE.
Important Notes:
NONE of the filters in the system are cleanable. They will all need to be removed and disposed of periodically.
See t
he “Filter Service & Replacement” Section for more info.