background image

2.   During the system booting the following message appears:

      *** Installation Failed: Intel  82365SL  PCMCIA Adapter not           

                  found.

      a. A hardware or software conflict may exist between the            

                        PCMCIA controller and some other device or program in       

                       the  system.

      b. The  PCD2-F  may be defective.

3.  The PC already contains a version of card and socket services.

      If the version of card and socket services is dated 1993 and          

                  before, the  PCD2-F  and any  Quatech PCMCIA card may not       
                  function.  Install the new version of card and socket services       

                  after removing the old version of the software.

4. During the installation of the  Cardsoft  Utility, the PC freezes        

                 operation while loading the drivers to the hard drive.

      a.  Not enough memory has been allocated.  The   Cardsoft            

                       utility needs a minimum of 1K of memory to load the             
                        drivers.  Consult the PC manual for information on how to   
                         free memory.

5.  There is an address conflict between the  PCD2-F  and an existing

                  device in the PC.

      a.  The  PCD2-F  can only use the address range of 03E0 - 03E7.     

                        Change the base of the  pre-existing  device if possible.

Please call  Quatech's  technical support department for further assistance
at (800) 553-1170, Monday through Friday, 8:00 AM to 6:00 PM EST.

__________________________________________________________________

14                                                                                                     

Quatech Inc.

Содержание PCD2-F















Отзывы: