Quatech MPAP-200 Скачать руководство пользователя страница 35

Страница: 35 / 64

9.5

SCC Incompatibility Warnings

Due to the SCC implementation used by the MPAP-200, there are two minor

incompatibilities that the software programmer must avoid.

9.5.1

Register Pointer Bits

In a Zilog 85230, the control port register pointer bits can be set in either channel. With

the implementation on the MPAP-200, however, both parts of an SCC control port access must
use the same I/O address.

IMPORTANT

The programmer must be certain not to mix channel usage during

the two-part access of SCC control ports. It would be highly

irregular for code to be written in such fashion, so this restriction is

not expected to be burdensome.

The following sequences will work:

Write Control Port A

(set pointer bits for desired register)

Read or Write Control Port A (read or write desired channel A register)

Write Control Port B

(set pointer bits for desired register)

Read or Write Control Port B

(read or write desired channel B register)

The following sequences will NOT work:

Write Control Port A

(set pointer bits for desired register)

Read or Write Control Port B (read or write desired channel B register)

Write Control Port B

(set pointer bits for desired register)

Read or Write Control Port A

(read or write desired channel A register)

9.5.2

Software Interrupt Acknowledge

The 85230's software interrupt acknowledge mechanism is not supported. Bit 5 of Write

Register 9 (Software INTACK Enable) is forced to 0. Software must employ the "Interrupt
Without Acknowledge" interrupt method using Read Registers 2 and 3 to process interrupts.

Содержание MPAP-200

































































Результаты поиска

Содержание MPAP-200

Отзывы:

Похожие инструкции для MPAP-200

Бренды по названию

Популярные бренды

Quatech MPAP-200, Руководство пользователя

Результаты поиска

Содержание MPAP-200

Отзывы:

Похожие инструкции для MPAP-200

Бренды по названию

Популярные бренды