Quatech AirborneDirect ABDB-SE Series Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 109

background image

100-8006-152G AirborneDirect™

Serial Bridge User’s Guide

Page 75

Quatech, Inc. Confidential

UDP INTERACTION

The Module includes UDP support. There are two configuration options to activate UDP. UDP
transmit can be enabled either in a “UDP” only or “both” mode.

The

UDP Target IP Address, UDP Target IP Port, UDP Transmit Mode,

and

UDP Listen Port

settings apply to UDP functions for the Bridge.

UDP Only Mode

The factory default UDP transmit and receive port number is

8023

. You can change this default

value using the settings

UDP Target Port and UDP Listen Port

.

UDP frames will be passed to the

UDP Target IP Address

and

UDP Target Port

address and/or broadcasted if

UDP Transmit Mode

is set to

bcast

or both, when the unit is

in PASS mode. In addition, UDP frames will be received on the

UDP Listen Port

when the

unit is in PASS mode.

Both Mode

A connection must be made using the TCP tunnel. UDP will transmit and receive
UDP frames (like in UDP only mode) when the TCP tunnel is established and
active. When the TCP connection closes, UDP operations halt. If the TCP tunnel
is active, thereby allocating the serial port, then received UDP datagrams will be
dropped.

HOST INTERACTION USING UDP

The UDP functions (between the Bridge and the Host) operate in pass-through mode. By factory
default, the Module starts up in master-Listen mode.

APPENDIX A

UDP AND POWER MANAGEMENT

«
...
79
80
81
82
83
...
»

Содержание AirborneDirect ABDB-SE Series














































































































Отзывы:

Нет отзывов

Похожие инструкции для AirborneDirect ABDB-SE Series

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Бренд: D-Link Страницы: 31

Бренд: DPtech Страницы: 39

Бренд: KPN Страницы: 14

Бренд: ZyXEL Communications Страницы: 116

Бренд: TP-Link Страницы: 2

Бренд: H3C Страницы: 4

Бренд: Watchguard Страницы: 21

Бренд: NETGEAR Страницы: 20

GlobeSurfer X-1

Бренд: Option Audio Страницы: 30

Бренд: Toto Link Страницы: 57

dLAN 200 AVsmart+

Бренд: Devolo Страницы: 2

Бренд: ZyXEL Communications Страницы: 645

DGN2200M - Wireless-N 300 Router

Бренд: NETGEAR Страницы: 95

Altusen SN0100 Series

Бренд: ATEN Страницы: 178

Бренд: Accusys Страницы: 12

Бренд: NetComm Страницы: 124

Бренд: Infrant Technologies Страницы: 2

Бренд: Acer Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды