Quasonix QSX-RDMS-RM Series Скачать руководство пользователя страница 18

Страница: 18 / 190

Rack-Mount RDMS

Telemetry Receiver

Quasonix, Inc.

Model Number

Code

Band

Minimum

Frequency

Maximum

Frequency

Default

Frequency

P, Full L, S, and C

(Five band)

400.0 MHz

5150.0 MHz

400.0 MHz

1.2.2

Options

The available options are listed below. Refer to section 1.2.3 for detailed descriptions of each option. Please contact
Quasonix for assistance ordering receiver options.

•

14 SAW filters (adds 70 kHz, 1.4, 3, 6, 14, and 28 MHz filters)

•

Continuous tuning

•

Digitally implemented pre-detection diversity combiner (requires dual-channel configuration)

•

K7 Viterbi Decoder (k=7, rate 1/2)

•

LDPC decoder

•

Blank front panel with no displays or keypad

•

RS-422 clock and data outputs on 3-lug triax connectors

•

Configure-Channel 2 the same as Channel 1 (bands and modes)

•

Extended C band

•

Extend frequency range for all enabled bands

•

Extended Lower L band

•

Extended P band

•

Extended S band

•

Extended Upper L band

For example, a model QSX-RDMS-RM2-L-1101-S-1101-DC is configured as shown in Table 2:

Table 2: Model Configuration Example

Identifiers

Description

QSX

Quasonix product

RDMS

Receiver / Demodulator / Bit Synchronizer

RM2

Rack-Mount package, 2 channels

Ch 1: Lower L-band operation

1101

Ch 1: Tier 0 present, Tier I present, Tier II absent,
Legacy (PSK) present

Ch 2: S-band operation

1101

Ch 2: Tier 0 present, Tier I present, Tier II absent,
Legacy (PSK) present

Содержание QSX-RDMS-RM Series































































































































































































Результаты поиска

Содержание QSX-RDMS-RM Series

Отзывы:

Quasonix QSX-RDMS-RM Series, Инструкция по установке и эксплуатации, Страница: 18 / 190

Результаты поиска

Содержание QSX-RDMS-RM Series

Отзывы: