manualshive.com logo in svg

Quasonix QSX-RDMS-RM Series, Инструкция по установке и эксплуатации, Страница: 19 / 190

Поделиться
Скачать
Quasonix QSX-RDMS-RM Series Скачать руководство пользователя страница 19

 

Rack-Mount RDMS

TM

 Telemetry Receiver 

 

4

 

 Quasonix, Inc. 

 

Identifiers 

Description 

DC 

Diversity combiner option 

 

In the case of multi-channel receiver configurations with identical frequency bands and modes, a shorthand part 
number can be used by including a multiplier code immediately following the initial frequency band and mode 
character string. The multiplier code is “X2” for applicability to a two channel receiver configuration. 

As an example, the following traditional part number, QSX-RDMS-RM2-M-1110-M-1110-DC, can be shortened to 
QSX-RDMS-RM2-M-1110-X2-DC. 

1.2.3 

Detailed Option Descriptions 

1.2.3.1 

SAW Filter Option 

– 14 

This option adds additional SAW filters, for a total of 14. The additional filters are 70 kHz, plus 1.4, 3, 6, 14, and 28 
MHz. 

1.2.3.2 

Continuous Tuning 

– CT 

The CT option allows continuous tuning, including between specified bands. This option only applies to five-band 
receivers. 

1.2.3.3 

Diversity Combiner 

– DC 

The DC option provides a digitally implemented pre-detection diversity combiner. This option requires the dual-
channel configuration. 

1.2.3.4 

Viterbi Decoder (for Legacy PSK Only) 

– K7 

The K7 option (k=7, rate 1/2) enables Viterbi decoding of a convolutionally encoded data stream, which converts it 
back to the original (uncoded) source data stream. 

Convolutional encoding adds redundant information to the transmitted data stream to help detect and correct bit 
errors that may occur, particularly due to predominantly Gaussian noise. Use of convolutional encoding requires a 
matching Viterbi decoder in the receiver to extract the source data. The decoded data rate is half the encoded data 
rate. The receiver has two independent decoders, one for in-phase (“I”) data and one for quadrature (“Q”) data. For 
BPSK, only a single decoder is used. Each decoder is compatible with the convolutional encoding described in the 
“Consultative Committee for Space Data Systems, Recommendation for Space Data System Standards, TM 
Synchronization and Channel Coding, CCSDS 131.0-B-1, Blue Book, September 2003, Section 3.” 

1.2.3.5 

Forward Error Correction/Low Density Parity Check (LDPC) (SOQPSK Only) 

– LD 

The LD option provides the Low Density Parity Check (LDPC) forward error correction (FEC) decoder. This option 
is only available with SOQPSK. 

1.2.3.6 

No Display 

– ND 

The ND option provides a blank front panel with no displays or keypad. 

1.2.3.7 

RS-422 

– RS 

The RS option specifies RS-422 clock and data outputs on 3-lug triax connectors. 

1.2.3.8 

Clone Channel 2 

– X2 

The X2 option specifies Channel 2 configuration to match the Channel 1 bands and modes. 

Содержание QSX-RDMS-RM Series































































































































































































Отзывы:

Нет отзывов