background image

http://www.bestmaterials.com      |      1-800-474-757

0

[email protected]    |      

http://www.bestmaterials.com      |      1-800-474-7570

     [email protected]    |      http://www.bestmaterials.com      |      1-800-474-7570

http://www.bestmaterials.com      |      1-800-474-757

0

[email protected]    |      

http://www.bestmaterials.com      |      1-800-474-7570

      [email protected]    |      http://www.bestmaterials.com      |      1-800-474-7570

         

Distributed by Best Materials® LLC

3. Vent Placement on Ridge

Attach vent to the roof deck by driving a nail in 
each of the two corners on both ends of the vent. 
Also, drive two nails through the vent and foam 
end  cap  to  hold  foam  in  place  on  the  ends  of 
the ridge only. Nails should penetrate the wood 
roof  deck  at  least 

3⁄4”

.  It  is  not  recommended  to 

nail vent to ridge prior to cap shingle installation. 
Because  of  the  popularity  of  dimensional 
roofing  material  such  as  the  newer  40/50  year 
and  lifetime  laminated  shingles,  we  require 
that  a  bead  of  sealant  be  applied  to  the  roof 
shingles  before  installing  the  vent  on  the  ridge. 

This  sealant  should  fill  any  voids  between  the 
bottom of the vent and the surface of the shingle. 
Use  either  butyl sealant conforming to ASTM C1085, 
latex sealant conforming to ASTM C834, silicone 
sealant  complying  with  ASTM  C920  or  asphalt 
roofing  cement  complying  with  ASTM  D4586. 
Roll  out  or  place  Quarrix  Ridge  Vent  along  the 
entire length of slot also covering the 6” minimum 
uncut  ridge  on  both  ends.  Bend  vent  into  a  “V” 
Shape.  Secure  at  the  lead  edge  after  inserting
the end cap. 

Nail  should  penetrate  roof  deck  a  minimum  of 

3⁄4”

. Pull the vent tight and secure at about 10’. Pull 

the rest of the vent tight and secure, inserting the 
end cap. Multiple lengths of vent can be joined 
by butting the sections tightly together. End caps 
should  be  inserted  at  the  beginning  and  end 
of  each  section.  Do  not  pre-fasten  ridge  vent 
along the entire vent; with Quarrix Ridge Vent’s  
One-Pass™  Installation,  it  is  not  necessary  to  
pre-fasten  the  vent  every  2’  to  3’  prior  to  cap  
shingle installation.

INSTALLATION INSTRUCTIONS     

ATTIC PROTECTION

Quarrix.com  

 800.438.2920

1

2

3

2

INST-SSRV01.0

2

.0

4.

21

Содержание StormStop














Отзывы: