background image

 

 

 

QK-A035 Manual                                                     

  

 

V 1.0 

7  of  19 

2021 

TAKE CARE: There may be two GND connections on your NMEA 0183-RS232 device. 

One is GND for the NMEA Connection, and one is GND for Power.   

Ensure you check the above table and your device’s documentation carefully before connection. 

3.1.2.  Connecting to NMEA 0183 (RS422) devices   

For RS422 interface devices, these wires need to be connected   

3.3 SeaTalk

¹

 

The built-in SeaTalk

1

 to NMEA converter translates SeaTalk¹ data into NMEA sentences. The SeaTalk¹ 

port has 3-pin terminals for connection to the SeaTalk¹ bus. Ensure the wires are connected correctly 
before powering up your devices as an incorrect connection could damage the A035 and other devices 
on the SeaTalk¹ bus. 

The SeaTalk¹ converter converts the Seatalk¹ messages as per the conversion table below. When a 
SeaTalk¹ message is received, the A035 checks if the message is supported. When the message is 
recognized as being on the SeaTalk¹ data table (below), the message is extracted, stored, and 
converted to an NMEA sentence. Any unsupported datagrams are ignored. These converted NMEA 
messages are filtered and then combined with NMEA data received on the other inputs. 

This function allows the NMEA multiplexer to listen on the SeaTalk¹ bus. Only one SeaTalk¹ input is 
needed since the SeaTalk¹ bus is a single-cable system that connects all the instruments together 
through one cable. The SeaTalk¹ to NMEA converter in the A035 works in one direction only. No NMEA 
sentences are converted into SeaTalk¹.   

Supported SeaTalk Datagrams 

SeaTalk 

NMEA 

Description 

00 

STDBT 

Depth below transducer 

10 

STMWV  Wind angle, (10 and 11 combined) 

11 

STMWV  Wind speed, (10 and 11 combined) 

20 

STVHW 

Speed through water, includes heading when 
present 

21 

STVLW 

Trip mileage (21 and 22 combined) 

22 

STVLW 

Total mileage (21 and 22 combined) 

23 

STMTW 

Water temperature 

25 

STVLW 

Total and Trip mileage 

26 

STVHW 

Speed through water, includes heading when 
present 

    NMEA OUT+        -----

 

    NMEA OUT-          -----

 

  GND * 

    NMEA RX 

* Swap two wires if the A035 does not work. 

QK-A035 wire 

Connection needed on RS422 device 

NMEA IN+                -----

 

NMEA IN-                -----

 

            NMEA OUT+ * 

            NMEA OUT- 

                      NMEA OUT+            -----

 

                      NMEA OUT-            -----

 

        NMEA IN+ * 

        NMEA IN- 

* Swap two wires if the A035 does not work. 

Содержание QK-A035




















Отзывы: