background image

After all the wiring connections are made and before the system is turned on

for the first time, you need to make some basic adjustments. It is important that

the High-Pass and Low-Pass Frequency Controls are set correctly before

turning on the system for the first time.

Setting the CrossoverFrequency Controls

1.

 Set the crossover frequency controls to the frequency recommended by the

speaker manufacturer.

. The following are some guidelines if this information

is not available: 

 Most 6” speakers will operate down to 80 - 100Hz. 

 Most 5” or 4” speakers will operate down to 100 - 150Hz. 

 Most 3” speakers will not operate below 300Hz. 

 Most subwoofers have decreased sound quality when operated above 

150Hz.

Depending upon the size of the front and rear speakers and the type of subwoofer system, fine tuning these
adjustments may be required after the initial system set-up. Study the system design pages of this manual to

determine the proper settings for these controls. Speakers are easily damaged if they are crossed over at a 

frequency below their usable range.

2.

 When making the high frequency adjustments, adjust the Low-Pass

frequency control and the low frequency amplifier gain.  Usually, the Low-

Pass frequency should be set the same as the High-Pass frequency

.

NOTE: An exception will be when the front/rear speaker is too small to play down to a very low frequency and the

subwoofer sounds distorted trying to “play up” to meet the front/rear speaker. This may require a gap or difference

between the high and low settings.  Although not ideal, this is sometimes neccessary to make the system work as

well as possible.

Setting the Front Output Level

Before setting front level controls, disconnect both the rear output and the

subwoofer output and follow the directions below

.

1. Turn the output control level to the minimum setting.
2. Turn the amplifier gain controls to the minimum setting.
3. Turn the source unit on and increase the volume until distortion is heard,

then reduce volume to just below this point.

NOTE: This is the maximum usable musical signal forthis source unit. turning the volume beyond

this point will increase noise and distortion without an increase in musical signal. If you can increase

the source unit volume to maximum without audible disortion, raise the output level controls slightly

and begin again.

4. With the amplifier gains still at minimum and the source unit set at

maximum volume without distortion, raise the front output level control

until distortion is heard, then reduce gain to just below this point. This is the

maximum output level for this system.  For best performance do not

increase beyond this point. 

2-Way System with Front and Rear Output

(Adjusting your System)

APPLICATIONS

10

www.quantumaudio.net

Содержание QA3X

















Отзывы: