5
Step 2: Attach fireplace insert into the unit as shown in Fig. H with 5 short KD screws [U].
(3 KD short screws at the top of the insert and 2 short KD screws at the Large “L”
bracket [Q]). See Fig. J.
Fig. J
BACk
Step 3: move assembled unit to desired location. Unit should not be positioned in area exposed
to direct sunlight.
WAll ANcHOr SAFEtY cABlE
The use of wall anchor safety cable is highly recommended in order to reduce the risk of the
fireplace being tipped over accidentally.
wARNING: THIS CABlE MAy REDUCE POSSIBlE RISk OF INJURy IF THE
FIREPlACE IS IMPROPERly HANDlED, BUT IS NOT A SUBSTITUTE FOR PROPER
ADUlT SUPERVISION. CHIlDREN SHOUlD NOT BE lEFT UNATTENDED NEAR
ANy HEATER.
1. Drill a 5/16 in (8 mm) hole in the wall. Insert the plastic wall anchor into the hole and gently
tap until the flange on the anchor is against the wall surface.
2. Position the back edge of the mantel close to the wall.
3. Attach the safety cable to the mantel using the screw for mantel.
4. Use the screw for wall to attach the other end of safety cable to the wall.
5. make sure all screws are tight.
OPErAtiON
After reading complete instructions, confirm all controls on fireplace are in the OFF position.
Plug the fireplace into a 15AmP/120volt outlet. If the cord does not reach, you may use an
extension cord rated for a minimum of 1875 WATTS. Once the fireplace insert has been
properly connected to a grounded electrical outlet, it is ready to operate.
OPErAtiON BY tHE cONtrOl PANEl
The controls are located behind the grill below the front glass and can be accessed by pulling
the grill from the top, forward and down.
wARNING: DO NOT TOUCH HOT SURFACE AT CENTRE OF GRIll, HANDlE, lEFT OR
RIGHT SIDE OF GRIll wHEN PUllING OUT.
O/I:
Press this switch for main power and flame effect. The indicator light will turn on. See
below for other control switches.
1250w:
For heat function - Press this switch while the O/I switch is in the ON position. The
indicator light will turn ON.
TEMPERATURE CONTROl:
To adjust the temperature to your individual requirements, turn the
temperature control dial to the right (clockwise) to increase the desired temperature and to the
left for lower temperature. This temperature control dial can only be used while the O/I switch
and 1250W switch are in the ON position.
NOTE:
When the O/I switch is turned off, the heater functions will stop even though the
switches may be in the ON position.
MAiNtENANcE
wARNING:
DISCONNECT POwER AND UNPlUG THE POwER CORD BEFORE ATTEMPTING ANy
MAINTENANCE OR ClEANING TO REDUCE THE RISk OF FIRE, ElECTRIC SHOCk OR
DAMAGE TO PERSONS. THE BUlB IN yOUR UNIT CAN BECOME ExTREMEly HOT.
AllOw AT lEAST 10 MINUTES BETwEEN TURNING OFF THE UNIT AND REMOVING
THE lIGHT BUlB TO AVOID THE ACCIDENTAl BURNING OF THE SkIN.
RISk OF FIRE: DO NOT ExCEED THE RECOMMENDED BUlB wATTAGE.
rEPlAciNG tHE FlAME EFFEct liGHt
AND lOG-SEt liGHt BUlB
Step 1: Remove the 12 screws on the back of fireplace and open the rear cover. There are 2
larger screws and 10 smaller screws
Step 2: You will find a 1 X 40W Type B-10 bulb under log-set bed.
Step 3: Loosen and remove the burnt out bulb and replace with a new bulb.
Step 4: Close the rear cover. Secure the 2 larger screws into the top left corner hole and
bottom right corner holes as shown in the diagram. Secure the 12 smaller screws into
the remaining holes. make sure the screws are in the correct holes and have been
tightened.
Step 5: Plug in the unit.