4
5
WARNING:
Procedures and techniques if not carefully
followed - will result in damage to the equip-
ment. - will expose the user to the risk of
serious injury, illness or death.
This electric fireplace heater is for use on
120 volts. The cord has a plug as shown at
A in illustration below. An adapter as shown
at C is available for connecting three-blade
grounding-type plugs to two-slot recep-
tacles. The green grounding plug extend-
ing from the adapter must be connected
to a permanent ground such as a properly
grounded outlet box. The adapter should not
be used if a three-slot grounded receptacle
is available.
A 15 AMP circuit is required to operate this
heater. If the breaker trips when the heater
is used then you may need to move the
heater to another location or unplug other
appliances that are on the same circuit. If
you require an extension cord use one that is
rated at 1875 watts.
IMPORTANT
Please note when you open the carton care-
fully check the unit and make sure there are
no damages. If you have any problems with
the unit, with how the various functions work
or with hidden damages or missing parts
please call 1-800-459-4409 (EST) immedi-
ately for service. NOTE: DO NOT RETURN
UNIT TO THE STORE BEFORE CALLING THE
TOLL FREE NUMBER. Do not dispose of your
cartons until you are completely satisfied
with your new fireplace heater. Read all in-
structions thoroughly before operating your
new Electric Fireplace.
NOTE: Light bulbs may become loose during
shipping. If the flame effect is dim or does
not work, please check that light bulb or
bulbs are finger tight in socket. See instruc-
tions for replacing bulb or bulbs. Please do
not return the sample to the store before
checking light bulbs.
NOTE: The electric fireplace heater may emit
a slight harmless odor when first turned
on. This is caused by activating the internal
heater components for the first time and
should not occur again.
WARNING: Do not load articles more than
40 lbs (18.2kg) on the drop leaf, which may
cause product damage or personal injury.
S A F E T Y I N S T R U C T I O N S
A S S E M B LY I N S T R U C T I O N S
PARTS LIST:
A) Top panel
1
B) Base panel
1
C) Decorative bar
1
D) Upper-front panel 1
E) Lower-front panel 1
F) Left front panel
1
G) Right front panel
1
H) Left small panel
1
J) Right small panel
1
K) Left side panel
1
L) Right side panel
1
M) Drop leaf
1
N) Left Triangle support 1
P) Right Triangle support 1
Fireplace insert
1
Q) KD screws
60
R) Mounting clips
S) Small screws
6
T) Plastic connectors 16
U) WALL ANCHOR SAFETY CABLE
Wall anchor
1
Screw for wall anchor 1
Screw for mantle
1
Safety cable
1
V) SELF REPAIR SET
Touch-up repair paint (bottle)
L shape bracket
8
Screws for L shape
2
Plastic connector
1
KD screws
KD nuts
W) Mounting bracket 2
X) Short KD screws
fig. A
TOOL REQUIRED: PHILLIPS HEAD SCREWDRIVER
MANTLE ASSEMBLY:
CAUTION: Place a piece of cardboard or
protective sheet on the floor in order to avoid
scratching the decorative surface of your
mantle during assembly.
Please DO NOT fully tighten the KD screws
until all panels are assembled.
NOTE: If the KD screw(s) do not fit during
assembly, loosen the 2 screws to adjust
the Plastic Connector until the PANEL/KD
SCREWS are able to be installed. Tighten all
KD screws once all panels are assembled.
Step 1: Attach all PLASTIC CONNECTOR (T) to
the PANELS (C, H, J, K and L) as shown in Fig.
A. (2pcs KD SCREWS for each CONNECTOR)
