Qualcast QG-BC 30, Оригинальная инструкция по эксплуатации

Страница: 20 / 32

Helpline No. UK 0151 649 1500 / IRE 189 094 6244 Helpline No. UK 0151 649 1500 / IRE 189 094 6244
16
order to remove the blade.
5.1.4 Installing the cutting line guard hood
Important: The cutting line guard hood must be
fitted if you wish to work with the cutting line. The
guard hood for the cutting line must be installed
using the 3 screws as shown in Figures F1 - F3.
A blade (Fig. F6/ Item A) on the underside of the
guard hood automatically cuts the cutting line
to the optimum length. This is covered by a ‘u’
shaped guard (Fig. F6/Item B).
Remove the ‘u’ shaped guard before you start
working and replace it when you have finished
working.
5.1.5 Fitting / Replacing the line spool
Line up the hole in the collar with the ‘u’ shaped
recess in the drive housing, and use the locking
Bar to secure the drive shaft, whist you fit the line
spool assembly (Fig. F4/F5).
Important: Left-hand thread! Rotate the spool
counter-clockwise to tighten and clockwise
to loosen).
To dismantle, proceed in reverse order.
5.2 Setting the cutting height (Fig. G1-G6)
Fit the carrying strap.
Hook the machine to the carrying belt (Fig.
G5). Adjust the perfect working and cutting
position using the various strap adjuster on
the carrying strap (Fig. G1 - G4). In order to
establish the optimum length of the carrying
strap, you should then make a few swinging
movements without starting the engine (Fig. G6).
Please note: Always use the shoulder strap
when using the machine. Attach the strap as
soon as you have started the engine and the
engine is running in idle mode. Switch off the
engine before you take off the shoulder strap.
Check the machine for the following each
time before use:
• That there are no leaks in the fuel system
• That the cutting unit and all safety devices
are in perfect condition
• That all screws are securely fastened
5.3 Fuel and oil
Recommended fuels
Use only a mixture of normal unleaded petrol
and special 2-stroke engine oil. Mix the fuel
mixture as indicated on the fuel mixing table.
Please note: Do not use a fuel mixture which
has been kept for longer than 90 days.
Please note: Do not use 2-stroke oil with a
recommended mixing ration of 100:1.
If inadequate lubrication causes engine
damage, the manufacturer’s engine
warranty will be voided.
Please note:
Only use containers designed
and approved for the purpose to transport
and store fuel. Pour the correct quantities of
petrol and 2-stroke oil into the mixing bottle
(Fig. C/Item 22 see scale printed on the
bottle). Then shake the bottle well.
5.4 Fuel mixture table
Mixing procedure: 40 parts petrol to 1 part oil
Petrol 2-stroke oil
1 litres 25 ml
5 litres 125 ml
6. Operation
Important. A blade (Fig. F6/ Item A) on the
underside of the safety guard automatically
cuts the cutting line to the optimum length.
6.1 Starting the engine when cold
Fill the tank with the required amount of oil/
petrol mix. See “Fuel and oil”.
1. Set the machine down on a hard, level
surface.
2. Set the choke position (Fig. A/Item 10) to „ “.
3. Press the fuel pump (primer) (Fig H/Item 16)
10 times.
4. Switch the ON/OFF switch (Fig. A/Item 6) to “I”.
5. Hold the machine firmly in position with one
hand.
6. With the other hand pull out the starter
cable (Fig. A/Item 11) until you feel it starts
to resist. Then tug sharply on the starter
cable 10 times.