Qualcast QG-BC 30, Оригинальная инструкция по эксплуатации

Страница: 19 / 32

Helpline No. UK 0151 649 1500 / IRE 189 094 6244 Helpline No. UK 0151 649 1500 / IRE 189 094 6244r
15
3. Proper use
The machine is designed for cutting lawns and
grassed areas.
Important. Due to the high risk of bodily injury
to the user, the brush cutter must not be used to
carry out the following work: to clean (suck up)
dirt and debris off walkways, or to chop up tree
or hedge clippings. Moreover, the brush cutter
may not be used to level out high areas such as
molehills. For safety reasons, the brush cutter may
not be used as a drive unit for other work tools or
toolkits of any kind.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case
of misuse. The user / operator will be liable for any
damage or injuries of any kind caused as a result
of this. Please note that our equipment has not
been designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the machine is used in commercial, trade or
industrial businesses or for equivalent purposes.
4. Technical data
Engine type: 2-stroke engine, air-cooled,
chrome cylinder
Engine power (max.): 0.76 kW/1.03 hp
Displacement: 29.7 cc
Idle speed of engine: 2900 rpm
Max. engine speed: 11000 rpm
Max. twin line speed: 8000 rpm
Max. blade speed: 11000rpm
Ignition: Electronic
Drive: Centrifugal clutch
Weight (with empty tank): 7.5 kg
Long handle length: 135 cm
Cutting circle diameter of line: Ø 43 cm
Cutting blade diameter: Ø 23 cm
Cutting line length: 5.0 m
Cutting line diameter: 2.0 mm
Tank capacity: 0.6 l
Spark plug: Torch L8RTC
Vibration ahv rear handle: 9.319 m/s 2
Uncertainty of vibration level: 3.7m/s 2
L
pA
sound pressure level: 92 dB (A)
L
WA
sound power level: 112 dB (A)
Uncertainty sound level: 1dB
5. Before starting the equipment
5.1 Assembly
5.1.1 Installing the additional handle
Install the additional handle (LH and RH
halves) as shown in Figures D1 - D4.
Do not fully tighten the screws until you have
set the perfect working position with the
carrying strap. The additional handle halves
should be aligned as shown in Figure A.
5.1.2 Assembly of the long handle (Fig. D6 - D7)
Remove the transport guard cap from the
lower long handle. Slacken the star grip screw
(Fig. D6/Item A) on the connecting piece
on the upper long handle (Fig. D6/Item B).
Carefully slide the lower long handle (Fig. D6/
Item C) into the connecting piece on the
upper long handle.
When doing so, take care to ensure that
the drive shafts on the insides of the long
handles slide into each other (turn the spool
head gently, if required) and that the lock on
the lower long handle (Fig. D7/Item D) latches
securely in the connecting piece.
Now retighten the star grip screw (Fig. D6/Item
A). To dismantle, proceed in reverse order.
5.1.3 Fitting/Replacing the blade (Fig. E1-E4)
- Fit the Blade Guard (Fig. E1/Item 2) to the bottom
of the drive unit & secure with the 3 screws.
- Fit the Drive Collar (Fig. E3/Item 28) over the
splines on the drive shaft. Line up the hole in
the collar with the ‘u’ shaped recess in the drive
housing (Fig. E1 & E3). Then fit the blade (Item 4)
onto the shoulder of the collar. (The blade is
reversible, so either way up, is O.K).
- Fit the Blade Clamp Collar (Fig. E2/Item 29) on top
of the blade, and then fit the LH Threaded nut
(Fig. E2/Item 27), counter-clockwise until finger
tight. Insert the locking Bar (Fig. C/Item 23) into
the hole in the Drive Collar & use the Spark
Plug Wrench (Fig. C/Item 21) to tighten the nut.
(Important, LH thread = rotate the part/
spanner counter-clockwise to tighten and
clockwise to loosen).
- To remove the Blade, rotate the assembly until
the hole in the Drive Collar lines up with the ‘u’
shaped recess in the drive housing, before
using the tools and proceeding in the reverse
Sound and vibration were measured in
accordance with EN ISO 27917, 10884/7916.