Qualcast HQ-CG 3.6, Оригинальная инструкция по эксплуатации

Страница: 13 / 18

Helpline No. UK 0151 649 1500 / IRE 189 094 6244 Helpline No. UK 0151 649 1500 / IRE 189 094 6244
11
slightly during the charging operation.
This is normal.
• As soon as battery pack is fully charged, the
red LED (Fig. 5/Item 1) extinguishes.
If the rechargeable battery fails to charge, check
whether there is voltage at the socket outlet.
Timely recharging of the battery pack will help
it serve you well for a long time. Recharging is
always necessary when you notice a drop in
the tool’s performance.
Never allow the battery pack to become
fully discharged. This will cause it to
develop a defect.
5.2 Fitting the long handle
Using the telescopic long handle (Fig. 1/Item
5) you can push the cordless trimmer on
wheels over the lawn.
To fit the long handle, push the mount (Fig. 3a/
Item 8) onto the long handle until the lock (Fig.
3a/Item 1) engages in one of the recesses on
the mount. The equipment is provided with
one recess at the top for standard cutting and
two recesses on the left and right for cutting
edges. Now pass the wheels (Fig. 3b/Item 2)
through the axle mount and push together.
Undo the clamp coupling (Fig. 1/Item 6),
adjust the telescopic handle to the required
length and then retighten the clamp coupling
again. Now push the trimmer unit in the
direction indicated by the arrow into
the mount (Fig. 4a/Item 8) as shown in Figure
4a. Ensure that the mount locks into the
recesses correctly. Then connect the power
plug (Fig. 4b/Item 1) to the equipment as
shown in Figure 4b. To disassemble, proceed
in reverse order.
Important!
It is prohibited to remove or bridge any of
the switching elements installed on the tool
by the manufacturer (e.g. by securing a
button to the handle) as this would prevent
the tool from switching off automatically
and result in high risk of injury. Under no
circumstances are you to use the shrub
cutter with the telescopic long handle fitted.
6. Operation
The area to be cut must first be cleared of
stones and other solid objects. The safety
lock-off (Fig. 1/Item 3) prevents the tool being
started unintentionally. Activate the safety lock-
off (Figure 1 / Item 3) by pushing it forward and
pressing the ON/OFF switch (Figure 1 Item 4) at
the same time. To switch off the tool, let go of
the ON/OFF switch (Figure 1 / Item 4).
6.1 Cutting grass
Allow the grass cutter to glide above the
ground. The best results are achieved when
the lawn is dry.
When you notice a drop in
cutting performance, recharge the tool
immediately so that the battery does not
become fully discharged.
6.2 Trimming hedges
The tool can be used to trim small hedges
and shrubs.
Hold the tool slightly tilted in relation to the
hedge you want to cut. First cut the sides from
the bottom up, then cut the top.
Watch out for foreign objects in or on the
hedge which could damage the blades.
When is the best time to trim hedges?
• As a general rule, hedges which lose their
leaves in the autumn should be trimmed in
June and October.
• Hedges which do not lose their leaves
should be cut in April and August.
6.3. Changing the blades
Important. Risk of injury!
Always fit the protective cover to the blades
before changing the blades on the unit.
To remove the blades, raise the lug (Fig. 6/Item 1)
and push off the cover (Fig. 6/Item 2) in direction
of the arrow. Once you have removed the
blade you will be able to see the toothed
wheels of the gear unit (Fig. 7). Make sure that no
dirt gets into the gear unit when you change the
blade. To assemble, proceed in reverse order.