Quadra-Fire XPLRMED-PBK Скачать руководство пользователя страница 6

 6 

 

 

 

 

                        7061-197H 

 

 

 

       November 10, 2015

Explorer II Medium Wood Stove

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual.

 

Customer: 

 

     

 Date Installed: 
 Lot/Address:
 Location of Fireplace:

 Installer

.Dealer/.Distributor.Phone.#:

.Serial.#:.

 Model (circle one):    

EXPLRMED-PBK      EXPLRMED-PDB      EXPLRMED-PFT      EXPLRMED-PMH      EXPLRMED-MBK

WARNING! Risk of Fire or Explosion! 

Failure to install fireplace according to these instructions can lead to a fire or explosion.

Appliance Install                                                                                              

Verified clearances to combustibles. (Pg. 8)

Hearth extension size/height decided. (Pg. 14) 

Outside air kit installed. (Pg. 15)

Floor protection requirements have been met.

If appliance is connected to a masonry chimney, it should be cleaned and 

inspected by a professional. If installed to a factory built metal chimney, the 

chimney must be installed according to the manufacturer’s instructions and 

clearances. 

Chimney

.Section.4.(Pg..11)

Chimney configuration complies with diagrams.

Chimney installed, locked and secured in place with proper clearance. 

Chimney meets recommended height requirements (14-16 feet).

Roof flashing installed and sealed.

Terminations installed and sealed.

Clearances

.Section.3.(Pg..7)

Combustible materials not installed in non-combustible areas.

Verified all clearances meet installation manual requirements.

Mantels and wall projections comply with installation manual requirements. 
Protective hearth strips and hearth extension installed per manual requirements.

Appliance Setup

.Section.5.(Pg..14)

All packaging and protective materials removed. 

Firebrick, baffle and ceramic blanket installed correctly. 

All labels have been removed from the door.

All packaging materials are removed from inside/under the fireplace.

Manual bag and all of its contents are removed from inside/under the fireplace

     and given to the party responsible for use and operation.

Hearth.&.Home.Technologies.recommends.the.following:

• Photographing the installation and copying this checklist for your file.
• That this checklist remain visible at all times on the fireplace until the installation is complete.

Comments: 

Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:

Comments communicated to party responsible                                                         by                                             on                    
  

 

 

 

          

(Builder/Gen. Contractor)                           (Installer)                        (Date)

Part # 4017-254 • Rev B • 01/29/13

YES...... IF.NO,.WHY?

F..

Install Checklist

Содержание XPLRMED-PBK





















Отзывы: