background image

Quadra-Fire  •  Columbia Bay Insert  •  7002-109  Rev. H  •  10/08

2

APPROVED FOR CANADA AND USA TO:
ANSI Z21.88b-2003 / CSA 2.33b-2003 Vented Gas Fireplace Heate r, and applicable sections of UL307b Gas Burning
Heating Appliances for Manufactured Homes and Recreational Vehicles, CAN/CG A 2.17-M91 “Gas Fired Appliances
for use at High Altitudes.”
This appliance is manufactured for operation with Natural Gas. For conversion to propane the Manufacturer’s kit
provided with the stove must be used in conjuntion with the instructions in the owner's manual.
This vented gas fireplace heater is not for use with air filters.
This appliance may be installed in a bedroom or bedsitting room; in Canada remote thermostat installation is
required.

FAN TYPE VENTED CIRCULATOR Blower Electrical Rating115 V., 1.5 Amps, 60 Hz, 150 Watts

For use with Natural Gas

For use with Propane

"0-2000’

"0-2000’

Input Rate on “HI” (BTU/Hr)

30,000

28,000

Input Rate on “LO” (BTU/Hr)

22,500

22,650

Main Burner Orifice (DMS)

36

52

Minimum Inlet Pressure (Inches W.C.)

4.5”

11”

Maximum Inlet Pressure (Inches W.C.)

7.0”

14”

Manifold Pressure on “HI” (Inches W.C.)

3.5”

10”

Efficiency up to

82.5%

81%

AFUE

71%

72.5%

2005

2006

2007

Feb

Mar

Apr

May

Jun

Jul

Aug

Sep

Oct

Nov

Dec

Jan

DO NOT REMOVE THIS LABE

L

MADE IN U.S.A.

Date of Manufacture / Date du Manufacturier

MINIMUM CLEARANCES TO COMBUSTIBLES

This appliance equipped for altitudes 0-2000’ (0-610m) in USA; and in Canada for altitudes of 0-4500’ (0-1370m). In USA for
Altitudes above 2000’, the vent configuration, orifice, or combination of both may need to be changed. See Owner’s Manual for
information on making these changes.

This appliance must be installed in accordance with local codes, if any (and Commonwealth of Massachusetts approved); if
none, follow The National Fuel Gas Code,ANSI Z223.1 and NFPA 54; or Canadian Installation Codes CAN/CGA-B149.
NOTE: Have the gas supply line installed in accordance with local building codes by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth of Massachusetts, installation must be performed by a licensed
plumber or gas fitter.)

Manufactured by:

7031-221

P.4.1-02 Canada Minimum Pipe 69% NG / 71% LP

Report No. / Rapport Numero

061-S-63-5

MODEL: XXXXXXX

VENTED GAS APPLIANCE

NOT FOR USE WITH SOLID FUEL

SERIAL

NO.

XXX

Tested and

Listed by

Beaverton

Oregon USA

OMNI- Test Laboratories, Inc .

C

R

and Welcome to the Quadra-Fire Family

!

Hearth & Home Technologies welcomes you to our tradi-
tion of excellence!  In choosing a Quadra-Fire appliance, 
you have our assurance of commitment to quality, durabil-
ity, and performance.

This commitment begins with our research of the market, 
including ‘Voice of the Customer’ contacts, ensuring we 
make products that will satisfy your needs. Our Research 
and Development facility then employs the world’s most 
advanced technology to achieve the optimum operation of 
our stoves, inserts and fi replaces.  And yet we are old-fash-
ioned when it comes to craftsmanship.  Each appliance 

is meticulously fabricated and gold and nickel surfaces 
are hand-fi nished for lasting beauty and enjoyment.  Our 
pledge to quality is completed as each model undergoes 
a quality control inspection.   From design, to fabrication, 
to shipping: Our guarantee of quality is more than a word, 
it’s Quadra-Fire tradition, and we proudly back this tradition 
with a Limited Lifetime Warranty.  

We wish you and your family many years of enjoyment in 
the warmth and comfort of your hearth appliance.  Thank 
you for choosing Quadra-Fire.

SAMPLE OF SERIAL NUMBER / SAFETY LABEL

LOCATION: HANGING ON A CHAIN ON BACK OF APPLIANCE

Manufactured 
Date

Serial Number

Model Name

Test Lab & 
Report No.

Содержание Vented Gas Fireplace Heater COLBAY-INS






































Отзывы: