Quadra-Fire QV36A-FB Скачать руководство пользователя страница 44

Quadra-Fire  •  Expression 36 (QV36A-FB)  •  2062-900  Rev. S  •  11/11

44

B. Lighting Appliance

IPI  Ignition

1.

  This appliance is equipped with an ignition 

device which automatically lights the burner. 

DO NOT

 try to light the burner by hand.

2. 

Wait  fi ve (5) minutes to clear out any gas. 
Then smell for gas, including near the fl oor. If 
you smell gas, STOP! Follow “B” in the Safety 
Information located on the left side of this la-
bel. If you do not smell gas, go to next step.

3.

  To light the burner:    

 

Equipped with wall switch: Turn ON/OFF switch 
to ON.

 

Equipped with remote or wall control:  Press 
ON or FLAME button.

 

Equipped with thermostat: Set temperature to 
desired setting.                                                   

4.

  If the appliance does not light after three tries, 

call your service technician or gas supplier.

LIGHTING

INSTRUCTIONS (IPI)

TO TURN OFF

GAS TO APPLIANCE

1.

  Equipped with wall switch: Turn ON/OFF switch 

to OFF.

 

Equipped with remote or wall control:  Press 
OFF button.

 

Equipped with thermostat:  Set temperature to 
lowest setting.

2.

 Service technician should turn off electric 

power to the control when performing service.

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: 

If you do not follow these instructions exactly, a fi re or explosion 

may result causing property damage, personal injury or loss of life.

CAUTION:

NOT FOR USE 

WITH SOLID FUEL

WARNING:

593-913G

GAS

VALVE

For additional information on operating your

 Hearth & Home Technologies fi replace, please refer to www.fi replaces.com.

A.

 This appliance is equipped with an 

intermittent pilot ignition (IPI) device 
which automatically lights the burn-
er. 

DO NOT

 try to light the burner by 

hand.

B.

 

BEFORE LIGHTING,

 smell all around 

the appliance area for gas.  Be sure to 
smell next to the fl oor because some 
gas is heavier than air and will settle 
on the fl oor.

WHAT TO DO IF  YOU SMELL GAS

•  

DO NOT

 try to light any appliance.

• 

DO NOT

 touch any electric switch; do 

not use any phone in your building.

DO NOT CONNECT LINE VOLT-
AGE (110/120 VAC OR 220/240 
VAC) TO THE CONTROL VALVE.

Improper installation, adjustment, al-
teration, service or maintenance can 
cause injury or property damage. Re-
fer to the owner’s information manual 
provided with this appliance.

This appliance needs fresh air for 
safe operation and must be installed 
so there are provisions for adequate 
combustion and ventilation air.

If not installed, operated, and main-
tained in accordance with the manufac-
turer’s instructions, this product could 
expose you to substances in fuel or 
fuel combustion which are known to the 
State of California to cause cancer, birth 
defects, or other reproductive harm.

Keep burner and control compartment 
clean. See installation and operating 
instructions accompanying appliance.

Hot while in operation. 

DO NOT

 touch. 

Keep children, clothing, furniture, gaso-
line and other liquids having fl ammable 
vapors away.

DO NOT

 operate the appliance with 

fi xed glass assembly removed, cracked 
or broken. Replacement of the fi xed 
glass assembly should be done by a 
licensed or qualifi ed service person.

•  Immediately call your gas supplier 

from a neighbor’s phone. Follow the 
gas supplier’s instructions.

•   If you cannot reach your gas sup-

plier, call the fi re department.

C. DO  NOT

 use this appliance if any 

part has been under water. Imme-
diately call a qualifi ed service tech-
nician to inspect the appliance and 
to replace any part of the control 
system and any gas control which 
has been under water.

For use with natural gas and propane. 
A conversion kit, as supplied by the 
manufacturer, shall be used to convert 
this appliance to the alternate fuel.

Also Certifi ed for Installation in a 
Bedroom or a Bedsitting Room.

For assistance or additional informa-
tion, consult a qualifi ed installer, ser-
vice agency or the gas supplier.

Final inspection by                                                                            

Содержание QV36A-FB

























































Отзывы: