Quadra-Fire QF130 Скачать руководство пользователя

Страница: 29 / 41

Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11

A. Remove Glass Assembly

See Section 12.H.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the

ﬁ rebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated

inside the

ﬁ rebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included

with accessories. Contact your dealer for a list of ap-

proved accessories.

WARNING! Risk of Fire and Electric Shock!

Use ONLY

Hearth & Home Technologies-approved optional acces-

sories with this appliance. Using non-listed accessories

could result in a safety hazard and will void the warranty.

E. Place the Lava Rock

Appliance Setup

F. Ember Placement

WARNING! Risk of Explosion!

Follow ember placement

instructions in manual. DO NOT place embers directly over

burner ports. Replace ember material annually. Improperly

placed embers interfere with proper burner operation.

Ember material is shipped with this gas appliance. To place

the ember material:
• Embers CANNOT be placed directly over ports. Care

should be taken not to cover the lighting trail of ports

(from back to front).

• Place dime-size pieces of Glowing Embers® just in front

of the port trail, but not on or in between the ports (see

Figure 12.2). Care should be taken so that the ports are

not covered. Failure to follow this procedure will likely

cause lighting and sooting problems.

• Save the remaining ember materials for use during

appliance servicing. The embers provided should be

enough for 3 to 5 applications.

Figure 12.2 Placement of Embers

EMBERS NOT

ALLOWED IN

PILOT AREA

PLACE LAVA ROCK IN SHADED AREA ONLY

Figure 12.1 Placement of Lava Rock

WARNING! Risk of Explosion!

Follow lava rock place-

ment instructions in manual.

DO NOT place lava rock on

burner. Improperly placed lava rock interferes with proper

burner operation.

Lava rock is shipped with this gas appliance. To place

the lava rock:
• Lava rock CANNOT be placed on the burner.
• Place lava rock in front of and to the sides of the

burner.

Содержание QF130










































Результаты поиска

Содержание QF130

Отзывы:

Похожие инструкции для QF130

Бренды по названию

Популярные бренды

Quadra-Fire QF130, Руководство пользователя

Результаты поиска

Содержание QF130

Отзывы:

Похожие инструкции для QF130

Бренды по названию

Популярные бренды