background image

September 16, 2009

7014-188

Page  3

CB1200-I Pellet Insert

Section 1: Listing and Code Approvals

 

A.  Appliance Certifi cations ......................4

 

B.  Mobile Home Approved ......................4

 

C.  Glass Specifi cations ............................4

 

D.  Electrical Rating ..................................4

 

E.  BTU & Effi ciency Specifi cations ..........4

Section 2: Getting Started

 

A.  Design, Installation & Location

 

  

Considerations ....................................5

 

B.  Locating Your Appliance & Chimney ..6

 

C.  Thermostat Location ...........................6

 

D.  Draft ....................................................6

 

E.  Negative Pressure ..............................6

 

B.  Fire Safety ..........................................7

 

C.  Tools & Supplies Needed ...................7 
D.  Inspect Appliance, Components

 

  

and Pre-Check List .............................7

Section 3: Dimensions &  Clearances

 

A.  Appliance Dimensions ........................8

 

B.  Clearances to Combustibles

 

  

As A Built-In, UL and ULC ..................9

 

C.  Clearances to Combustibles, 

 

  

Masonry & Zero Clearance .................10

 

D.  Minimum Opening for Factory

 

  

Built Fireplace .....................................10

 

E.  Masonry Minimum Opening ................10

 

F.  Floor Protection ..................................10

 

G.  Calculating Alternate Floor

 

  

Protection Material ..............................11

 

H.  Prefabricated Metal Chimney .............11

 

I. 

Removing Floor of Factory Built

 

  

Fireplace .............................................12

 

J.  Altering Factory-Built Fireplace ...........12

Section 4: Vent Information

 

A. 

Chimney & Exhaust Connections

 ........1

3

 

B.  Venting Termination Requirements ....13 
C.  Equivalent Feet of Pipe.......................14 
D.  Pipe Selection Chart ...........................14 

 

Section 5:  Venting Systems

 

A.  Full Reline with Outside Air-Horizontal 15

 

B.   Full Reline with Outside Air-Vertical ....16

Section 6:  Mobile Home

 ..................................17

Section 7:  Appliance Set-Up

 

A.  Rear Shroud Installation .....................18-19

 

B.  Outside Air Kit .....................................20

 

C.  Adjustable Hopper Option...................20

 

D.  Grille Installation .................................20 
E.  Adjustable Hearth Support..................21

 

F.  Panel & Trim .......................................22-23

 

G.  Brick Set Installation ...........................24

 

H.  Brick Clip Installation ...........................24

 

I. 

Log Set Placement ..............................25 

J.  Thermostat Installation ........................25

Section 8:  Operating Instructions

 

A.  Fuel Size, Material & Storage .............26

 

B.  General Operation Information ...........27

 

C.  Before Your First Fire .........................27

 

D.  Starting Your First Fire ........................27

 

E.   Fire Characteristics .............................28

 

F.  Feed Rate Adjustment  .......................28

 

G.  Ignition Cycles ....................................28 
H.  Frequently Asked Questions...............29

Section 9: Troubleshooting

 ............................31-32

 

Section 10

Maintaining & Servicing Appliance

 

A.  Proper Shutdown Procedure ...............33

 

B.  Quick Reference Maintanence Chart ..33

 

C.  General Maintenance & Cleaning .......33-36

 

D.  High Ash Content Maintenance ..........37

 

E.  Glass Replacement .............................38

 

F.  Igniter Replacement ............................39

 

G.  Baffl e Removal ....................................39

Section 12: Reference Material

 

A.  Component Functions.........................40-41

 

B.  Component Locations .........................42

 

C.  Exploded Drawings .............................43

 

D.  Service Parts & Accessories...............44-48

 

E.  Service & Maintenance Log ................49 

 

E.  Warranty Policy ...................................50-51

 

F.  Contact Information ............................52

TABLE OF CONTENTS

     Safety Alert Key:

• 

DANGER!

 

Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• 

WARNING!

 Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• 

CAUTION!

 

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• 

NOTICE:

 Indicates practices which may cause damage to the fi replace or to property.

Содержание PELLET INSERT CB1200MI-MBK





















































Отзывы: