background image

 2 

 

 

 

 

                        7034-277B 

 

 

 

                 May 2, 2014

MT. VERNON AE

TABLE OF CONTENTS

     Safety Alert Key:

• 

DANGER!

 

Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• 

WARNING!

 Indicates a hazardous situation which, if not avoided may result in death or serious injury.

• 

CAUTION!

 

Indicates a hazardous situation which, if not avoided, may result in minor or moderate injury.

• 

NOTICE:

 Indicates practices which may cause damage to the appliance or to property.

Important Safety Information .............3

A.  Appliance Certification ......................................................3

B.  BTU & Efficiency Specifications........................................3

C.  Glass Specifications .........................................................3

D.  Electrical Rating................................................................3

E.  Mobile Home Approved .................................................... 3

Getting Started ....................................4

A. Design, Installation & Location Considerations  ..........................4

B. Thermostat Wall Control Location......................................5

C.  Tools And Supplies Needed ..............................................5

D. Inspect Appliance and Components  .................................5

E. Install Checklist ..................................................................6

Dimensions and Clearances ..............7

A.  Appliance Dimensions ......................................................7

B. Clearances to Combustibles (UL and ULC) .......................8

C. Hearth Pad Requirements (UL and ULC) ..........................8

Vent Information ..................................9

A.  Venting Termination Minimum Requirements ...................9

B. Avoiding Smoke and Odors ...............................................10

C. Negative Pressure .............................................................11

D. Draft ........ ..........................................................................11

E. Chimney and Exhaust Connection  ...................................11

F. Equivalent Feet of Pipe  .....................................................12

G. Pipe Selection Chart .........................................................12

Venting Systems ...............................13

A.  Alcove 13

B.  Through The Wall .............................................................14

C.  Vertical into Existing Class A Chimney .............................15

D. Through The Wall & Vertical - Exterior ..............................15

E. Vertical - Interior - Typical Installation ................................15

F.  Masonry.............................................................................16

G.  Alternate Masonry ............................................................16

Appliance Set-Up ..............................17

A.  Leg Leveling System  .......................................................17

B. Outside Air Kit Instructions ................................................17

C. Top Vent Adapter Installation  ............................................18

D. Rear Vent & Rear Vent to Top Vent Adapter Installation ....18

E. Optional Log Set Placement Instructions ..........................19

F.  Wall Control Thermostat Installation .................................20

Mobile Home Installation ..................21

Accessory List ..................................22

300 Watt Igniters come installed in brand new Mt. Vernon AE 

units and are for pellet fuel only. The 380 Watt Igniter is required 

for burning multi-gran fuels and is included in the component 

pack. Multi-fuels include, corn, sunflower seeds, and wheat. 

CONFIDENTIAL PROPERTY OF HEARTH & HOME TECHNOLOGIES INC.

PART NAME:

DRAWN BY:

SCALE:

MATERIAL:

SHEET:

PART NUMBER:

REV:

THIS PRINT IS CHECKED AND CONTROLLED BY THE ENGINEERING 

DEPARTMENTS OF HEARTH & HOME TECHNOLOGIES INC.

ECO #

DATE

BY

REV

UNLESS OTHERWISE SPECIFIED DIMS ARE INCHES[MM] & : TOLERANCES ARE:  (2) PLACE DEC : ± 0.03     (3) PLACE DEC: ± 0.005     ANGLE: ± 2°     FRACTION: ± 1/16

OUTSIDE MATERIAL.

NORMAL DIM & INSIDE MATERIAL.

OUTSIDE APEX

INSIDE APEX  -  DIMS ENCLOSED BY AN OVAL ARE CRITICAL DIMENSIONS

REVISIONS

ITEM

PART NUMBER

PART NAME

QTY

7034-280

MULTI-FUEL IGNITER

THIS IGNITER IS REQUIRED FOR 

BURNING FUELS OTHER THAN 

WOOD PELLETS.

THIS IGNITER CAN ALSO BE USED AS A 

BACKUP FOR WOOD PELLETS.

Содержание MTVERNON-AE-CSB

























Отзывы: