background image

May 5, 2015 

 

 

 

             

7036-188E 

 

 

 

         

                  17

MT VERNON AE INSERT

NOTE:  

Check clearances carefully for this type of instal-

lation to ensure adequate room for outside air venting.

Check building codes prior to installation.
•  Installation MUST comply with local, regional, state and 

national codes and regulations.

•  Consult local building, fi re offi cials or authorities having juris-

diction about restrictions, installation inspection, and permits.

CAUTION

NOTE:

  In Canada only a full reline is allowed per ULC 

S628, ORD ULC C1482-M1990.

B. Full Reline With Outside Air - Vertical 

Figure 17.1

Outside Air
Termination

at

 Chimney Top

(Vertical)

305mm  min.
below

305mm min.
above

NOTE;  Use metal plate around
exhaust vent pipe and seal all
edges with non-flammable insula-
tion such as fiberglass, mineral
wool or ceramic.

Do not use high temperature caulk-
ing materials to seal any edge to
prevent furture serviceability.

NOTE:  

In Canada this fi replace insert must be installed 

with a continuous chimney liner extending from the fi replace 
insert to the top of the chimney.  The chimney liner must 
conform to the Class 3 requirements of CAN/ULC-S635, 
Standard for Lining Systems for Existing Masonry or Facto-
ry-Built Chimneys and Vents, or CAN/ULC-S640, Standard 
for Lining Systems for New Masonry Chimneys.

Содержание MTVERNINSAE-PMH

























Отзывы: