Quadra-Fire MTVERNINSAE-CSB Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 24

background image

16

7036-188J

October 3, 2017

MT VERNON AE INSERT

5

Venting Systems

NOTE:

In Canada, where passage through a wall or partition of com-

bustible construction is desired, the installation shall conform

to CAN/CSA-B365.

Figure 16.1

Fire Risk.
Inspection of Chimney:
•  Masonry chimney must be in good condition.
•  Meets minimum standard of NFPA 211
•  Factory-built chimney must be a minimum 6 inch

(152mm) UL103 HT.

WARNING

CAUTION

Never draw outside combustion air from:

• Wall, floor or ceiling cavity

• Enclosed space such as an attic or garage

NOTE:

•

Illustrations reflect typical installations and are

FOR

DESIGN PURPOSES ONLY.

•

I

llustrations/diagrams are not drawn to scale.

•

Actual installation may vary due to individual design

preference.

A.

Full Reline With Outside Air - Horizontal

Outside Air through Rear

Wall (Horizontal)

NOTE; Use metal plate around

exhaust vent pipe and seal all

edges with non-flammable insu-

lation such as fiberglass, mineral

wool or ceramic.

Do not use high temperature

caulking materials to seal any

edge to prevent furture service-

ability.

«
...
14
15
16
17
18
...
»

Содержание MTVERNINSAE-CSB

























Отзывы:

Нет отзывов

Похожие инструкции для MTVERNINSAE-CSB

Бренд: Wayne Страницы: 46

Бренд: Wayne Страницы: 52

Бренд: Hargrove Страницы: 5

Бренд: Valor Страницы: 6

Бренд: Escea Страницы: 2

Бренд: Classics Страницы: 68

Nestor Martin 023

Бренд: Euroheat Страницы: 32

Бренд: Amantii Страницы: 33

Бренд: Contura Страницы: 12

Бренд: MHSC Страницы: 36

Бренд: ELEMENTI Страницы: 20

Бренд: Napoleon Страницы: 4

Бренд: Majestic Страницы: 26

Fletcher CM140-036

Бренд: Charmate Страницы: 4

Menards 198-6257

Бренд: Midwest Страницы: 9

Electronic Ignition Flame Control System

Бренд: HPC Страницы: 19

Бренд: Extraflame Страницы: 84

Бренд: Faber Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды