background image

Quadra-Fire  •  QVI-30FB  •  2020-900  Rev. H  •  9/07

19

Step 7.    Installing Logs and Ember Material

Positioning the Logs

The logs have been packaged separately. Refer to the
installation instructions that accompany this manual.

 Save

the log instructions with this manual.

If sooting occurs, the logs or glowing embers might need
to be repositioned slightly to avoid excessive flame
impingement.

Placing the Ember Material

Two separate bags of ember material are shipped with this
gas appliance. The bag labeled Glowing Ember (050-721)
is standard glowing ember material. To place the ember
material:

Remove the glass door from the unit (see Figure 12).

Figure 12.  Glass Assembly

Place a dime size piece of 

GLOWING EMBER

 mate-

rial near port holes in burner top, sides and front (see
Figure 13).

Space dime size ember pieces about a 1/2 inch apart.
Never press embers into burner ports. Do not cover burner
ports. Place dime size pieces around front and sides of
burner pan.

Save the remaining ember materials for use during fire-
place servicing. The embers provided are sufficient for 2
to 4 applications.

Place 

MYSTIC EMBERS

 over burner surface and around

base of the burner, do not cover any burner port holes.
Can be used on floor of firebox for a realistic ash-bed.

Replace the glass door on the fireplace.

Re-install and latch the decorative front.

Figure 13.  Placement of the Ember Material

Combustible materials 

MUST

NEVER

 overlap onto the front

face.

1. Find the coiled low voltage wires

and ON/OFF switch attached to
outer right side of the insert (see
Figure 14).

2. Disconnect the ON/OFF switch

from the low voltage wire leads,
and insert the ON/OFF switch
through the hole at the upper
right corner of the surround - it
will be retained in the hole.

Step 8.  Installing Trim
Surrounds

Figure 14.

___________________________________________

___________________________________________

Shutter Settings

Burner                                       

NG              LP

QVI-30FB                                  3/8”        Full Open

EMBER MATERIAL

(TOP SURFACE,

AND FRONT)

BURNER PAN

PULL AND

RELEASE

CLIPS TO OPEN

ON/OFF

SWITCH

SURROUND

WITH TRIM

FIREBOX

LOCATING

TABS

Î

Содержание Gas Firebrick qvi30fb


























Отзывы: