Quadra-Fire 7100FP Скачать руководство пользователя страница 17

Страница: 17 / 75

4/12

433-1390K

Page 17

Troubleshooting

This fireplace will operate correctly only if adequate ventila-

tion is provided to allow proper draft to the fireplace system.

Hearth & Home Technologies assumes no responsibility for

the improper performance of the fireplace system caused

by inadequate draft due to environmental conditions, down

drafts, tight sealing construction of the structure, or mechan-

ical exhausting devices which will create a negative air pres-
sure within the structure where the fireplace is located.
If smoke spillage occurs from a fireplace opening when the

door is open and the proper chimney height, flue size, and

configuration requirements for the installation have been

met, there is either a leakage in the flue, a blockage in the

flue, or some condition is in effect to draw smoke from the

fireplace into the house. Understanding and differentiating

the conditions which can cause each of these kinds of spill-

age problems is essential to their solution.
• Flue Leakage

Check for improperly connected flue joints or a damaged

flue joint in the chimney system. Such leakage would

reduce draft (air would be drawn in through the leaks rather

than through the fireplace). The result might be difficult

start-up and smoky fires that might spill if other adverse

draft conditions accompany this problem.

• Flue Blockage

The damper should be open.

or you find it difficult to establish and maintain a moderately

high burn rate, then the flue draft is too low and corrective

measures must be taken.
Be sure you have air available for combustion and that your

firewood is dry and well seasoned. Build your fires properly

and according to the instructions given in operating instruc-

tions, “Starting a Fire”. Be sure your flue system is installed

correctly and that it is the proper diameter and height. Check

for the following:
• All chimney sections are properly installed.

This fireplace will operate correctly only if adequate ventila-

tion is provided to allow proper draft to the fireplace system.

Hearth & Home Technologies assumes no responsibility for

the improper performance of the fireplace system caused by

inadequate draft due to environmental conditions, windy con-

ditions, down drafts, tight sealing construction of the structure,

or mechanical exhausting devices which will create a negative

air pressure within the structure where the fireplace is located.
Flue draft is measured as negative pressure in the chimney.

The amount of negative pressure determines how strong

the draft is. The draft is important because it draws the com-

bustion air into the fireplace and pulls the smoke out of the

chimney.

There are three basic criteria essential in establishing

and maintaining flue draft:

•  Availability of combustion air.
•  Heat generated from the fire.
•  Diameter and height of the flue system.
These three factors work together as a system to create

the flue draft. Increasing or decreasing any one of them will

affect the other two and thus change the amount of draft in

the entire system.
If the fire is hard to start and smoke spills out of the fireplace,

• The chimney is clean and free of creosote or soot

buildup.

• Make sure overhanging trees and branches are cut

back within ten feet of the top of the chimney and is

free of debris from animals.

• Ensure the chimney cap is clean and free of any

buildup of soot or creosote. if cap is equipped with a

spark arrestor screen.

• Be sure the ceramic blanket (above the baffle) and

the baffle are in their proper positions

• The wood being used in dry and well seasoned.

If you still suspect you have a low draft problem it may be

necessary to increase the volume of air in your flue system.

Since the diameter of your flue system is matched with the

size of the flue collar and should not be changed, then the

height of the system must be increased. Add chimney sections

a little at a time until the draft improves.
In some cases, regardless of what you do, it can still be dif-

ficult to establish the proper flue draft. This is especially evi-

dent when using an exterior factory-built chimney or exterior

masonry chimney. Try placing several sheets of crumpled

paper on top of your kindling as close to the flue outlet of

the fireplace as possible. Light this paper first then the paper

under the kindling. The heat generated from the rapidly

burning paper on top of the kindling should help get the draft

established.
Still other factors can affect how well your flue system per-

forms. Neighboring structures, high winds, tall trees, even

hillsides can affect air currents around the chimney. Well

designed chimney caps are available that can help. Your fire-

place dealer is the local expert in your area. He can usually

make suggestions or discover problems that can be easily

corrected allowing your fireplace to operate correctly as it

has been designed, providing safe and economical heat for

your home.

B. Draft Problems

A. Understanding Vent Problems

Содержание 7100FP












































































Результаты поиска

Содержание 7100FP

Отзывы:

Похожие инструкции для 7100FP

Бренды по названию

Популярные бренды

Quadra-Fire 7100FP, Руководство пользователя

Результаты поиска

Содержание 7100FP

Отзывы:

Похожие инструкции для 7100FP

Бренды по названию

Популярные бренды