quadient AS-CSD6 Скачать руководство пользователя страница 3

3

 

SAFETY PRECAUTIONS 

WARNING

 

THIS EQUIPMENT MUST BE CONNECTED TO A PROPERLY GROUNDED OUTLET!  FAILURE 
TO DO SO CREATES A POTENTIAL DANGER OF ELECTRICAL SHOCK! 

THIS EQUIPMENT PRESENTS NO PROBLEM WHEN USED PROPERLY.   

OBSERVE THE FOLLOWING SAFETY RULES WHEN OPERATING THE CONVEYOR. 

BEFORE USING THE CONVEYOR, YOU SHOULD READ THIS MANUAL CAREFULLY AND FOLLOW 
THE RECOMMENDED PROCEDURES, SAFETY WARNINGS, AND INSTRUCTIONS: 

 

Keep hands, hair, and clothing clear of rollers, belts, and other moving parts. 

 

Avoid touching moving parts or materials while the machine is in use.  Before clearing a jam, be sure machine 
mechanisms come to a stop. 

 

Always turn off the machine before making adjustments, cleaning the machine, or performing any maintenance 
covered in this manual. 

 

Use the power cord supplied with the machine. Plug it into a properly grounded wall outlet located near the 
machine and easily accessible. Failure to properly ground the machine can result in sever personal injury and/or 
fire. 

 

The power cord and wall plug are the primary means of disconnecting the machine from the power supply. 

 

DO NOT use an adapter plug on the line cord or wall outlet. 

 

DO NOT remove the ground pin from the line cord. 

 

DO NOT route the power cord over sharp edges or trapped between furniture. 

 

Avoid using wall outlets controlled by wall switches or shared with other equipment. 

 

Make sure there is no strain on the power cord caused by jamming between the equipment, walls, or furniture. 

 

DO NOT remove covers.  Covers enclose hazardous parts that should be accessed by a qualified service 
representative.  Report any damage of covers to your service representative. 

 

This machine requires periodic maintenance.  Contact your authorized service representative for service. 

 

To prevent overheating, do not cover the vent openings. 

 

Use this equipment only for its intended purpose. 

 

DO NOT allow the conveyor or dryer to operate unattended. 

 

Follow any specific occupational safety and health standards for your workplace or area. 

 

Dryer Safety Warnings/Precautions: 

 

The dryer should not be turned on unless the conveyor belts are moving. 

 

The dryer lamps, dryer surfaces and conveyor surfaces will get very hot and can cause injury. Keep all 
body parts, clothing, hair, and flammable materials away from the dryer and hot surfaces.  

 

If a flammable item comes in contact with the dryer or dryer lamps, there is a chance that it can catch fire. 
If a material jam occurs, turn off the conveyor and dryer immediately. Keep a properly rated fire 
extinguisher within reach when operating the dryer. 
 

This manual is intended solely for the use and information of Quadient, its designated agents, customers, and their 
employees. The information in this guide was obtained from several different sources that are deemed reliable by all 
industry standards. To the best of our knowledge, that information is accurate in all respects. However, neither 
Quadient, nor any of its agents or employees shall be responsible for any inaccuracies contained herein. 

All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means, electronic 
or mechanical, including photocopying, recording, or any information storage and retrieval system, without 
permission in writing from the publisher. 

 

 

Содержание AS-CSD6










Отзывы: