manualshive.com logo in svg

QUAD C4 - REV 1, Инструкция пользователя, Страница: 11 / 14

Поделиться
Скачать
QUAD C4 - REV 1 Скачать руководство пользователя страница 11

FROM

AMPLIFIER

TO NEXT

SPEAKER

11

WIRING & CONNECTIONS

Ensure that all wiring is installed in compliance with local laws, 

codes and convention. Obtain all necessary permits and approv-

als and use only cable that is approved for the application and is 

sized to safely accommodate the load.

Models C / CT / C6 / C8 and CSUB

These models include two internal crossover networks allowing 

either 4

Ω

 or 16

Ω

 low impedance operation. In addition they 

include 70/100V transformers for use in distributed systems. 

For 70/100V operation select the 

appropriate wattage tap using the 

rotary selector switch. Note that one 

side of the switch is labeled for 70V 

operation and the other side for 100V 

systems. Ensure that the power is set 

for the correct amplifier connected.

NOTE: 

DO NOT USE THE 

“0”

 

SETTING WHEN CONNECTED TO A 100V SOURCE!

Select the power tap by dividing the amplifier’s available power 

by the number of speakers to be connected and then selecting the 

next lower wattage tap. For example:

300W amplifier ÷ 20 speakers = 15 Watts; use the 

15W terminal

Individual speakers may be tapped higher or lower in order to 

better balance the system sound pressure level in different areas. 

Ensure that the combined power draw does not exceed the rated 

power of the amplifier or else damage to the amplifier and speak-

ers may occur. All 70/100V speakers should be wired in parallel 

as shown to the right.

Содержание C4 - REV 1















Отзывы:

Нет отзывов