background image

4.  General information

4. General information

4.1  About this manual

Manual code:

 DCMIINE0QIR100H

Revision:

 100

Copyright:

The information contained in this document is the sole property of Inim Electronics S.r.l.. Copy-

ing, reprinting or modification of this document, in part or as a whole, is not permitted without prior autho-

rization in writing from Inim Electronics S.r.l.. All rights reserved.

4.2  Manufacturer's details

Manufacturer:

 Inim Electronics S.r.l.

Production plant:

 Centobuchi, via Dei Lavoratori 10

63076 Monteprandone (AP), Italy

Tel.:

 +39 0735 705007

Fax:

 +39 0735 734912

E-mail

 [email protected]

Web:

 www.inim.biz

The persons authorized by the manufacturer to repair or replace the parts of this system have authorization 

to work only on devices marketed under the brand Inim Electronics.

4.3  Warranty

Inim Electronics S.r.l.. (Seller, Our, Us) warrants the original purchaser that this product shall be free from 

defects in materials and workmanship under normal use for a period of 24 months.
As Inim Electronics does not install this product directly, and due to the possibility that it may be used with 

other equipment not approved by Us;Inim Electronics does not warrant against loss of quality, degradation 

of performance of this product or actual damage that results from the use of products, parts or other repla-

ceable items (such as consumables) that are neither made nor recommended by Inim Electronics. Seller 

obligation and liability under this warranty is expressly limited to repairing or replacing, at Seller's option, any 

product not meeting the specifications. In no event shall Inim Electronics be liable to the purchaser or any 

other person for any loss or damage whether direct of indirect or consequential or incidental, including 

without limitation, any damages for lost profits, stolen goods, or claims by any other party caused by defec-

tive products or otherwise arising from the incorrect or otherwise improper installation or use of this product.
This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover 

damage arising from improper maintenance or negligence, damage caused by fire, flood, wind or lightning, 

vandalism, fair wear and tear.
Inim Electronics S.r.l. shall, at its option, repair or replace any defective products. Improper use, that is, use 

for purposes other than those mentioned in this manual will void the warranty. Contact Our authorized dea-

ler, or visit our website for further information regarding this warranty.

14

Installation and programming manual- 100

Содержание XLINE Series

















Отзывы: