6
TD-001532-01-A
Rear Panel
All inputs and outputs are configured in Q-SYS Designer software running on the Q-SYS Core to which the DCIO is connected.
— Figure 2 —
1
2
3
4
5
6
7
13
8
12
11
10
5
4
9
1.
INC / LNRE NRMAR
– Standard three-conductor XLR
connector, balanced input, phantom power available in
Q-SYS Designer. Used for: mono, non-sync sources including
microphone for in-auditorium announcements, and SPL metering.
Refer to — Figure 3 for wiring.
2.
Hearing Nmpaired and Visually Nmpaired Outputs
(H.N. and V.N.)
– Five-terminal Euro-style receptacle, balanced
outputs, used for: hearing- and / or visually-impaired special
mixes. The receptacle label provides a pin-out
of the signals. The ground is common to both. Refer to — Figure
4 for wiring.
RNM!:
A standard three-terminal Euro-style connector
may be used if only one output is required. Make sure the
plug is all the way to the right, or all the way to the left of
the five-terminal receptacle.
3.
AELWY OARMARS
– Two six-terminal Euro-style receptacles,
mechanically de-coupled control outputs, floating relay contacts,
rated for 30 VDC at 1A. Each relay output has one common
contact (C), one normally open contact (NO) and one normally
closed (NC) contact. When not energized, C is connected to NC
and NO is not connected. When energized, C is connected to NO
and NC is not connected. Used for controlling curtains, lighting,
etc.) Refer to — Figure 5 for wiring.
4.
WES3 NRMARS
– RJ45, CAT-5 or better to connect to sources
using the same type connector and pinout.
WES3 1–8
– AES3 pairs 1 through 4 (digital audio channels 1–8)
WES3 9-16
– AES3 pairs 5 through 8 (digital audio channels 9–16)
Used for primary content audio from the server or media block.
Refer to — Table 1 and — Table 2 for pin-out.
RORE!:
The AES3 connectors are NOT network
connections.
5.
LWR
connections – RJ45, CAT-5E or better.
LWR W
– Used for primary Q-LAN connection, required.
LWR B
– Used for redundancy.
6.
MO EA OR / OFF
switch
7.
NEC CORRECROA
– AC mains power connector
8.
Line Nnputs (LA)
– Standard 3.5mm TRS jack, unbalanced,
stereo, analog, line-input. Used for non-sync sources appropriate
for alternative content, advertising, corporate or live event feeds.
9.
IORNROA OARMARS
– Five-pin, Euro-style connector;
three-pins for Line
and two pins for Speaker
.
The supplied connectors have an extended tab with holes for
securing the wiring to the connector. Refer to — Figure 6 and the
pin-out label on the rear panel for wiring.
a.
LNRE
– The Line output provides a balanced output at 14 dBu,
via three pins of the Euro-style connector.
b.
SMEWKEA
– Powered output, 10 watts maximum, via two
pins of the Euro-style connector.
RNM!:
A standard two- or three-terminal plug may be
used if only one output is required.
10.
WAROIWRNOR NRMARS
– RJ45, contact closures. The
Automation Inputs can be connected to relay contacts or a switch
(control presets, mute etc). Refer to — Table 3 for the connector
pin-out.
11.
AS-232 Serial Communications
– Three-pin Euro-style
connector for (Rx), transmit (Tx) and ground pin. Used for third-
party control or automation. Refer to — Figure 7 for wiring.
12.
HDIN Nn
– DCIO-H
model only. Extracts audio
from incoming HDMI stream and passes
the stream directly to output HDMI port for connection to a
downstream video device. Up to 8 channels of PCM audio are
supported. Additionally, Dolby Digital Plus™ and DTS-HD®
decoders will be automatically applied if those bitstreams are
detected.
13.
HDIN Out
– DCIO-H model only. See HDMI In.
