QSC LA108 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 50

QSC LA108 Скачать руководство пользователя страница 49

49

Temporary Outdoor Use

The L Class products may be deployed outdoors on a temporary basis (music festivals, events, etc.). While the enclosures and power
connectors are IP rated, extra caution should always be taken in case of inclement weather. For these situations, it is recommended to
use the Temporary Weather Shield accessory to cover the Rear I/O’s situated on the loudspeakers' rear panel.

TWS-IO

Temporary Weather Shield covers input/output section of each LA108/LA112

Sub-stacking

LA108 Loudspeaker

The LA108 loudspeaker can be stacked over the LS118 subwoofer (upright or on its side), the KS118 (upright only), or the KS212C (on
its side only). For stack deployment over these subwoofers, the following accessories are required:

LA108-AF

Array Frame for LA108

LA108-KIT-SA

Stack Adapter Kit (includes 2x metal plates and hardware to be attached to LA108-AF array frame)

LA112 Loudspeaker

The LA112 loudspeaker can only be stacked over the LS118 subwoofer on its side. To stack over this subwoofer, the following
accessories are required:

LA112-AF

Array Frame for LA112

LA112-KIT-SA

Stack Adapter Kit (includes 2x metal plates and hardware to be attached to LA112-AF array frame)

Flown (Portable or Installed)

The LA108 and LA112 loudspeaker can each be flown in an array of up to six (6) boxes. It is recommended to use the following Array
Frame accessories:

LA108-AF

Array Frame for LA108

LA112-AF

Array Frame for LA112

Flown (Installed Only)

For cost-sensitive installations, the LA108 and LA112 loudspeakers can each be flown in a smaller array of up to three (3) boxes when
using the following Installation Kit:

LA-KIT-I

Installation Kit for LA108/LA112 (includes 2x Shackle Adapters and 1x Pullback Eyebolt)

Additional Information

Care and Maintenance

The LA108 and LA112 do not contain user-serviceable parts. QSC does not recommend using chemicals or solvents to wash
loudspeakers. Instead, use a damp towel with water only, and dry immediately after wiping down. Do not allow water to pool on the
rigging, hardware, or rear user interface.

If exposed to direct sunlight for extended periods of time, the hardware and ABS parts may become discolored or faded. Cover or
shade your LA108 or LA112 loudspeakers from long-term, direct sunlight whenever possible.

«
...
47
48
49
50
»

Содержание LA108



















































Отзывы:

Нет отзывов