QSC LA108 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 50

QSC LA108 Скачать руководство пользователя страница 40

40

Daisy-Chaining Procedure

1. Insert the locking POWER-OUT connector of the jumper cable (not supplied) fully into the OUTLET connector on the loudspeaker’s

rear panel. Twist clockwise until it locks in place.

2. Insert the locking POWER-IN connector into the INLET connector on the rear panel of the next loudspeaker in the chain. Twist

clockwise until it locks in place.

3. Repeat until all loudspeakers in the array (up to six (6), using five (5) loop-thru jumper cables) are properly connected.

Please follow the table below to safely power a specific loudspeaker array.

NOTE:

The QSC LS118 is a single 18-inch, active subwoofer, part of the L Class family of products, designed to

complement LA108/LA112 loudspeakers.

Model

Input Current (Normal Use)

100V (15A Circuit)

120V (15A Circuit)

220~240V (10A Circuit)

LA108

100V = 0.8A
120V = 0.8A
220~240V = 0.5A

Up to 6x loudspeakers
Total 4.8A

Up to 6x loudspeakers
Total 4.8A

Up to 6x loudspeakers
Total 3A

LA112

100V = 1.8A
120V = 1.5A
220~240V = 1.0A

Up to 6x loudspeakers
Total 10.8A

Up to 6x loudspeakers
Total 9A

Up to 6x loudspeakers
Total 6A

LS118

100V = 3A
120V = 3A
220~240V = 1.5A

Up to 4x subwoofers
Total 12A

Up to 4x subwoofers
Total 12A

Up to 4x subwoofers
Total 6A

It is also possible to mix and match subwoofers with arrayed loudspeakers when pole-mounting or ground-stacking them close
together. However, the QSC LA-KIT (both J and J-/NA versions) will need to be extended with a second jumper cable or compatible
Powercon TRUE1 cable to connect the uppermost subwoofer to the lowermost arrayed box.

NOTE:

PowerCON TRUE1 cables have a plug-end and a socket-end that can be daisy chained together to create

longer power connections.

Recommended Configurations

LA108 Loudspeaker

• 1x LS118 subwoofer with 3x LA108 loudspeakers pole mounted above (total 5.4A/100~120V or 3A/220~240V)
• 2x LS118 subwoofers with 4x LA108 loudspeakers in a ground-stack (total 9.2A/100~120V or 5A/220~240V)

LA112 Loudspeaker

• 2x LS118 subwoofers with 2x LA112 loudspeakers pole mounted above (total 9.6A/100, 9A/120V or 5A/220~240V)
• 2x LS118 subwoofers with 3x LA112 loudspeakers in a ground-stack (total 11.4A/100V, 10.5A/120V or 6A/220~240V)

WARNING!:

Always ensure the circuit is loaded no higher than 80% of the circuit rating when daisy-chaining AC power

to multiple boxes. For example, never load more than 12 Amps on a 120 V/15 A circuit, or 8 Amps on a 230 V/10 A
circuit.

«
...
38
39
40
41
42
...
»

Содержание LA108



















































Отзывы:

Нет отзывов