background image

11

The 215PCM requires 120 Volt, 30 Amp AC
service. Attempting full power operation on
lower rated circuits may overheat wirirng
and cause breakers to switch off.
Use only heavy-duty 12 or 10 ga. extension
cords.

The 215PCM requires a 120 Volt, 30 Amp connection to the AC mains.
The power connectors used are to be NEMA L5-30, or equivalent. The
serial number plate is imprinted with the operating voltage informa-
tion.

At peak output power, the 215PCM can supply up to 6,600 watts of
music power. At these levels, the AC line current can easily reach
levels in excess of 20 Amps. Proper AC connections are required at
such high power levels.

Connect the 30 Amp twist-lock connectors by orienting the locking L-
shaped prong with the corresponding connector entry, then fully insert
the three prongs. Twist the plug about 1/8 of a turn clockwise to lock
the connector and plug.

215PCM AC  connection.  The keyed connector fits only one way. Align the “L” shaped tang with the mating

receptacle and fully insert, then twist 1/8 turn clockwise to lock in place. Reverse procedure to remove plug.

CONNECTIONS- AC Power

AC Power Connection

AC Power Switch

Above and to the right of the AC entry connector is the Power switch. The switch is labeled POWER ON, above it.

To turn the power on:

 Press in on the upper portion of the rocker switch. Both DSP-3’s blue Power indicators

should illuminate.

To turn the power off: 

Press in on the bottom portion of the rocker switch. It may take a few moments for

the Power LED’s to extinguish. This is normal.

Power  switch.

Содержание ISIS 215PCM











































Отзывы: