7
Rigging the Installation Line Array (continued)
1- Working Load Limits are per fastener loaded in double shear. Data is for informational purposes only.
Attaching WL2082-i to Array Frame
Before beginning any installation, have your system designer configure the array with proper
splay angles using QSC’s EASE Focus (Array Calculator). All orientation of product is to be as
viewed from the rear of the enclosure.
Attach the array frame to the suspension structure using a 3/4” (20 mm) screw pin anchor
shackle and appropriate sling, cable, etc....
For arrays of 4 WL2082-i or less, assemble the cluster of WL2082-i on the ground using the
included mating hardware. Ensure the notched rigging plate is on the right hand side (the sys-
tem can only be installed one way. Note the QSC logo on the input plate will be right side up
when the enclosure is oriented properly). During assembly, ensure your splay angles are as
desired.
When constructing large arrays it is recommended to first assemble units of four enclosures
and then assemble the final array by joining the four enclosure units to one another.
Attachment of one enclosure to another is accomplished by inserting the cap-head shoulder
bolt with washer through the rigging plate attachment holes and appropriate splay angle
selection holes in the mating rigging plates and threading the lock nut (nylock) on the inside
edge of the plates. The bolt should be tightened snuggly to no more than 5 lb-ft of torque (6.8
N-m). See Figure 7 for assembly detail.
Attach the array frame to the top enclosure by inserting the cap-head shoulder bolt with
washer through the appropriate mounting holes and threading the lock nut (nylock) on the
inside edge of the plates. The bolt should be tightened snuggly to no more than 5 lb-ft (6.8 N-m)
of torque.
NOTE: For some array configurations, use of the extension bar and/or pull-back
may be required to achieve the required aiming angle.
Table 1: ILA Working Load Limits
Component
Weight
7:1 Design Factor
10:1 Design Factor
12:1 Design Factor
EB2082-i Extension Bar
38 lb (17.3 kg)
1714 lb (779.2 kg)
1200 lb (545.5 kg)
1000 lb (454.5 kg)
FB2082-i Array Frame
17 lb (7.7 kg)
740 lb (336.4 kg)
518 lb (235.5 kg)
432 lb (196.2 kg)
PB2082-i Pull Back Bar
6 lb (2.7 kg)
423 lb (192.2 kg)
296 lb (134.5 kg)
247 lb (112.1 kg)
WL2082-i Loudspeaker
37 lb (16.8 kg)
634 lb (288.3 kg)
445 lb (201.8 kg)
371lb (168.6 kg)
WL115-sw Loudspeaker
111 lb (50.5 kg)
740 lb (336.4 kg)
518 lb (235.5 kg)
432 lb (196.2 kg)
M8 Shoulder Bolt
1
not applicable
1003 lb (455.8 kg)
702 lb (319.1 kg)
585 lb (265.9 kg)
M8 Ball-lock Pin
1
not applicable
1810 lb (822.7 kg)
1267 lb (575.9 kg)
1056 lb (479.9 kg)
M8 Locking Plate
1
not applicable
1286 lb (584.4 kg)
900 lb (409.1 kg)
750 lb (340.9 kg)
M12 Shoulder Bolt
1
not applicable
4744 lb (2156.3 kg)
3321 lb (1509.4 kg)
2767 lb (1257.8 kg)
3/8” Fastener
1
not applicable
1943 lb (883.4 kg)
1360 lb (618.4 kg)
1134 lb (515.3 kg)
7/8” Fastener
1
not applicable
8110 lb (3686.4 kg)
5677 lb (2580.5 kg)
4731 lb (2150.4 kg)
Figure 7: WL2082-i attached to FB2082-i
