9
TD-001585-01-B
ABCD 1 Channel, ABCD Parallel
EFGH 1 Channel, EFGH Parallel
Parallel Channels (ABCD) and (EFGH)
— Figure 10 —
CHANNEL CONFIGURATION
1 Channel: A B C D
Channel Configuration Locked to Design
Q ABCD
CH ABCD
T3
+
T4
-
CH D
CH A
CH B
CH C
+
+
+
+
-
-
-
-
T8
T5
T6
T7
T4
T1
T2
T3
CH E
CH H
CH G
CH F
+
+
+
+
-
-
-
-
T1
T4
T3
T2
T5
T8
T7
T6
OUTPUTS TO SPEAKERS
OUTPUTS TO SPEAKERS
CHANNEL CONFIGURATION
Channel Configuration Locked to Design
Q EFGH
1 Channel: E F G H
CH EFGH
T1
+
T3
+
T5
+
T7
+
T2
-
T4
-
T6
-
T8
-
In 4-1 Parallel (ABCD or EFGH) only
T1+, T3+, T5+, and T7+ are electrically the same point
T2-, T4-, T6-, and T8- are electrically the same point
Possible Combinations
The table below lists the options available in Q-SYS Designer.
For One Loudspeaker
Full power to one loudspeaker; Use one 2-wire cable, connect to:
• T3+/T4- (Loudspeaker ABCD)
For Multiple Loudspeakers
Full power for multiple loudspeakers in parallel Use up to four 2-wire
cables, connect to:
• T1+/T2- (Loudspeaker E)
• T3+/T4- (Loudspeaker F)
• T5+/T6- (Loudspeaker G)
• T7+/T8- (Loudspeaker H)
Outputs
Configuration / Channels
Outputs
Configuration / Channels
A B C D
4 Channel
E F G H
4 Channel
A+B C D
3 Channel, A B Bridged
E+F G H
3 Channel, E F Bridged
A+B C+D 2 Channel, A B Bridged C D Bridged
E+F G+H 2 Channel, E F Bridged G H Bridged
AB C D
3 Channel, A B Parallel
EF G H
3 Channel, E F Parallel
AB C+D
2 Channel, A B Parallel C D Bridged
EF G+H
2 Channel, E F Parallel G H Bridged
AB CD
2 Channel A B Parallel C D Parallel
EF GH
2 Channel E F Parallel G H Parallel
AB+CD
1 Channel, A B Parallel Bridged with C D Parallel EF+GH
1 Channel, E F Parallel Bridged with G H Parallel
ABC D
2 Channel A B G Parallel
EFG H
2 Channel E F G Parallel
ABCD
1 Channel A B C D Parallel
EFGH
1 Channel E F G H Parallel
A B = Individual Channels, AB = Parallel Channels, A+B = Bridged Channels
Connect the Loudspeakers
WARNING!
There is a potential of having dangerous voltage at the
output terminals on the rear of the amplifier. Use caution not to touch
these contacts. Make sure the Power switch is off prior to making
any connections.
NOTEE:
The output connector is capable of handling up to 8 AWG for
stranded wire.
1. Connect the loudspeaker wiring to the 8-pin Euro-style connector as needed for your
amplifier's configuration.
2. Install the female 8-pin Euro-style connector onto the male connector on the rear of the
amplifier as shown in
Figure 11
.
3. Use a Phillips screwdriver to secure the connector.
IMPORTANT!
The DPA-Q series of audio power amplifiers are
high power amplifiers designed for installation use in both Lo-Z and
Hi-Z applications. Proper wiring class/size is required to ensure safe
operation. Based on operating mode, these amplifiers are designed for
use with the following speaker wiring:
• FAST Channel Configuration Mode: Single Channel & Parallel = Class 2 wiring
— Figure 11 —
All manuals and user guides at all-guides.com
