background image

LED

Status

Description

USB

Flashes blue every 0.5 sec

• A USB device (connected to the front USB port) is

detected.

• A USB device (connected to the front USB port) is

being removed from the NAS.

• A USB device (connected to the front USB port of the

NAS) is being accessed.

• Data is being copied to or from a USB or eSATA

device.

Blue

A USB device is detected in the front USB port.

Off

• No USB device is detected.

• The NAS has finished copying data to or from the USB

device connected to the front USB port.

Audio Alert

Duration

Frequency

Description

Short beep (0.5 seconds) 1

• The NAS is starting up.

• The NAS is shutting down (software shutdown).

• The user pressed the Reset button.

• The operating system was updated.

3

The user tried to copy the NAS data to the external
storage device from the front USB port, but the data
cannot be copied.

Long beep (1.5 seconds) 3 (every 5 minutes)

The system fan is not functioning.

2

• The disk volume is about to reach its full

capacity.

• The disk volume has reached its full capacity.

• The drives are in degraded mode.

• The user started the drive rebuilding process.

• A drive is plugged in or out.

1

• The NAS was powered off by force shutdown

(hardware shutdown).

• The NAS was powered on successfully and is

ready.

TS-x83XU User Guide

Basic Operations   

36

Содержание TS- 83XU Series



















































Отзывы: