manualshive.com logo in svg

QMS Magicolor WX, Руководство пользователя

Поделиться
Скачать
QMS Magicolor WX Скачать руководство пользователя страница 17

Set up the Printer

1-7

Setup

Set up the Printer

»

Note: 

The illustrations accompanying the following procedures show 

the printer sometimes from the front and sometimes from the rear, 
depending on which view is best to show you the part we’re installing 
at the time. You don’t need to turn the printer while performing these 
procedures.

Install the Developer and Toner Cartridges

M

WARNING!

 The developer and toner cartridge contain highly 

combustible powders; they should not be disposed of by burning. 
Also, avoid inhaling loose developer or toner or getting them around 
your eyes; they can cause respiratory problems and eye irritation.

ACHTUNG!  

Bei Entwickler und Toner handelt es sich um gefährliche 

Pulver, die leicht enzündlich sind; sie dürfen deshalb niemals mit 
offenem Feuer in Beruhrüng kommen. Einatmen oder Berührung mit 
Haut und Augen ist ebenfalls zu vermeiden, da dieses zu 
Beeintràchtigungen der Atemwege, Haut oder Augenreizungen 
führen könnte.

▲

Caution: 

It’s important to load the developer and toner cartridges in 

the correct place, exactly as described.

1

Find the black-developer cartridge and remove it from its 
protective bag. 

Developer cartridges have green handles and a small strip of 
plastic on top that indicates their color.

»

Note: 

Store all of the packing materials where you can easily 

access them if you ever need to relocate the printer or return it for 
service.

Содержание Magicolor WX

























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды