QMS
®
4060
Large-Capacity Input Feeder for Legal-size Media (LCIF -Legal)
1
1760255-001A
Installation
Guide
Caution:
We highly recommend that you have
an authorized QMS service techni-
cian install your QMS 4060 as well as
the optional large-capacity input
feeder.
However, if you do install this option yourself (or if you ever move the printer and this option), you must make
certain that the option aligns correctly with the printer.
This document provides quick installation information for the large-capacity input feeder for legal-size media.
For complete information, refer to appendix C, “Installing Options,” in the
Getting Started
manual or chapter 6,
“Hardware Options,” in the
Options
manual (on the
4060 Print System Documentation
CD-ROM).
Installation of the LCIF-Legal may require a call to your authorized service provider. If the engine prom (EPROM) part is marked with #1001598D or a lower alpha
character, then an upgrade is required. If the EPROM is labelled #1001598E or higher, an upgrade is not necessary. Installation of the EPROM by a non-
authorized service organization or individual will void the warranty of the printer and the LCIF. In addition, this option also requires system code rv2.1.3.
Check the startup page; if the system code is not rv2.1.3 or higher, refer to chapter 9, “Troubleshooting,” in the
QMS 4060 Print System Operation
manual on your
QMS 4060 Print System Documentation
CD-ROM to update the printer’s software. This enables the engine to recognize the Large-Capacity Input Feeder for legal-
size media.
Installing the Large-Capacity Input Feeder (LCIF-Legal)
The Large-Capacity Input Feeder for legal-size media (LCIF-Legal) holds 3000 sheets and increases the paper input capacity of the QMS 4060 Print System to 4500
sheets. The LCIF-Legal supports only plain paper 17–24 lb (64–90 g/m²). Thick paper, greater than 24 lb (90 g/m²), prepunched, and predrilled paper are not recom-
mended.
Caution:
Proper alignment of the LCIF to the printer is extremely important. Improper alignment causes frequent media jams. A firm, level surface is
necessary to achieve alignment. If you are placing your printer and LCIF on a soft carpeted floor, be sure you place a firm material, such as a chair
mat, under the units for stability.
The depth of the LCIF-Legal is 17.6" (446 mm). The LCIF-Legal requires the following clearances when you are installing this option:
Item
Clearance
Item
Clearance
Item
Clearance
Left side
Printer attach side
Front
25.6" (650 mm)
Height
23.6" (600 mm)
Right side
37.4" (950 mm)
Rear
33.5" (850 mm)
For final positioning of the printer and LCIF-Legal, make sure to allow enough room for the door of the input feeder to open completely (without having to move the
unit). Unnecessary movement of the printer and feeder can cause misalignment between the two units, and jams occur as a result.
WARNING!
The LCIF-Legal weighs approximately 41 lb. (18.6 kg). Do not attempt to lift or move it by yourself.
ACHTUNG!
Der LCIF-Legal wiegt ca. 18.6 kg; bitte versuchen Sie niemals, das Gerät alleine anzuheben oder zu tragen.
Unpack all items from the
box.
Save the packing material
for possible repacking.
Locate the support stand,
the support stand bracket,
and the sheet guide.
Turn off the printer and
open the front door.
Using a Phillips
screwdriver, remove the
right-side paper input cover
by loosening the front
screw and removing the
rear screw.
Attach the sheet guide to
the printer using the screws
you loosened and removed
earlier.
Install the support stand
bracket using the screws
attached.
Lift the support stand and
place it on top of the
support stand bracket.
Attach the support stand to
the support stand bracket.
Pull out the support stand
slide-rails until they lock in
the out position.
Set the LCIF on the pins of
the slide-rails.
Secure the LCIF to the
support stand using the
thumbscrews.
1
2
3
..
........
..
......
4
5
6
!
